Jeep WRANGLER 2021 Owner'S Manual Download Page 36

Page: 36 / 464

GETTING TO KNOW YOUR VEHICLE

wheel outward or push it inward as desired. To

lock the steering column in position, push the

control handle upward until fully engaged.

EATED

TEERING

HEEL

— I

QUIPPED

The steering wheel contains a heating element

that helps warm your hands in cold weather.

The heated steering wheel has only one

temperature setting. Once the heated steering

wheel has been turned on, it will stay on until

the operator turns it off. The heated steering

wheel may not turn on when it is already warm.
The heated steering wheel control button is

located within the climate or controls screen of

the touchscreen.



Push the heated steering wheel button

once to turn the heating element on.



Push the heated steering wheel button a

second time to turn the heating element off.

NOTE:

The engine must be running for the heated

steering wheel to operate.
For information on use with the Remote Start

system, see

page 22.

SEATS

Seats are a part of the Occupant Restraint

System of the vehicle.

WARNING!

Do not adjust the steering column while driv

ing. Adjusting the steering column while driv

ing or driving with the steering column

unlocked, could cause the driver to lose con

trol of the vehicle. Failure to follow this warn

ing may result in serious injury or death.

WARNING!



Persons who are unable to feel pain to the

skin because of advanced age, chronic

illness, diabetes, spinal cord injury, medica

tion, alcohol use, exhaustion, or other phys

ical conditions must exercise care when

using the steering wheel heater. It may

cause burns even at low temperatures,

especially if used for long periods.



Do not place anything on the steering wheel

that insulates against heat, such as a

blanket or steering wheel covers of any type

and material. This may cause the steering

wheel heater to overheat.

WARNING!



It is dangerous to ride in a cargo area,

inside or outside of a vehicle. In a collision,

people riding in these areas are more likely

to be seriously injured or killed.



Do not allow people to ride in any area of

your vehicle that is not equipped with seats

and seat belts. In a collision, people riding

in these areas are more likely to be seri

ously injured or killed.



Be sure everyone in your vehicle is in a seat

and using a seat belt properly.

21_JL_OM_EN_USC_t.book Page 34

Summary of Contents for WRANGLER 2021

















































































































































































































































































































































































































































































Search results

Summary of Contents for WRANGLER 2021

Reviews:

Jeep WRANGLER 2021, Owner'S Manual, Page: 36 / 464

Search results

Summary of Contents for WRANGLER 2021

Reviews: