Jeep WRANGLER 2021 Page 357 Owner'S Manual Download

Page: 357 / 464

IN CASE OF EMERGENCY

355

Disconnecting The Jumper Cables
1. Disconnect the negative (-) end of the

jumper cable from the engine ground of

the vehicle with the discharged battery.

2. Disconnect the opposite end of the

negative (-) jumper cable from the

negative (-) post of the booster battery.

3. Disconnect the positive (+) end of the

jumper cable from the positive (+) post of

the booster battery.

4. Disconnect the opposite end of the

positive (+) jumper cable from the remote

positive (+) post of the discharged vehicle.

5. Reinstall the protective cover over the

remote positive (+) post of the discharged

vehicle.

NOTE:

If frequent jump starting is required to start your

vehicle you should have the battery and

charging system tested at an authorized dealer.

IF YOUR ENGINE OVERHEATS

If the vehicle is overheating, it will need to be

serviced by an authorized dealer.
In any of the following situations, you can

reduce the potential for overheating by taking

the appropriate action.



On the highways — slow down.



In city traffic — while stopped, shift transmis

sion into NEUTRAL, but do not increase

engine idle speed.

NOTE:

There are steps that you can take to slow down

an impending overheat condition:



If your Air Conditioner (A/C) is on, turn it off.

The A/C system adds heat to the engine

cooling system and turning the A/C off can

help remove this heat.



You can also turn the temperature control to

maximum heat, the mode control to floor and

the blower control to high. This allows the

heater core to act as a supplement to the

radiator and aids in removing heat from the

engine cooling system.

CAUTION!

Accessories plugged into the vehicle power

outlets draw power from the vehicle’s battery,

even when not in use (i.e., cellular devices,

etc.). Eventually, if plugged in long enough

without engine operation, the vehicle’s bat

tery will discharge sufficiently to degrade bat

tery life and/or prevent the engine from

starting.

CAUTION!

Driving with a hot cooling system could dam

age your vehicle. If the temperature gauge

reads HOT (H), pull over and stop the vehicle.

Idle the vehicle with the air conditioner turned

off until the pointer drops back into the nor

mal range. If the pointer remains on HOT (H),

and you hear continuous chimes, turn the

engine off immediately and call for service.

21_JL_OM_EN_USC_t.book Page 355

Summary of Contents for WRANGLER 2021

















































































































































































































































































































































































































































































Search results

Summary of Contents for WRANGLER 2021

Reviews:

Related manuals for WRANGLER 2021

Brands by name

Popular brands

Jeep WRANGLER 2021, Owner'S Manual

Search results

Summary of Contents for WRANGLER 2021

Reviews:

Related manuals for WRANGLER 2021

Brands by name

Popular brands