Home
/
Jeep
/
Grand Cherokee SRT8 2012
/
Owner'S Manual

Jeep Grand Cherokee SRT8 2012, Owner'S Manual

Share

Page: 30 / 572

Jeep Grand Cherokee SRT8 2012 Owner'S Manual Download Page 30

How To Use Remote Start

All of the following conditions must be met before the
engine will remote start:

•

Shift lever in PARK

•

Doors closed

•

Hood closed

•

Liftgate/Flipper Glass closed

•

Hazard switch off

•

Brake switch inactive (brake pedal not pressed)

•

Ignition key removed from ignition switch

•

Battery at an acceptable charge level

•

RKE PANIC button not pressed

•

System not disabled from previous remote start event

•

Vehicle theft alarm not active

•

Ignition in Off position for Keyless Enter-N-Go vehicle

WARNING!

•

Do not start or run an engine in a closed garage or
confined area. Exhaust gas contains Carbon Mon-
oxide (CO) which is odorless and colorless. Car-
bon Monoxide is poisonous and can cause serious
injury or death when inhaled.

•

Keep Remote Keyless Entry (RKE) transmitters
away from children. Operation of the Remote Start
System, windows, door locks or other controls
could cause serious injury or death.

28

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
28
29
30
31
32
...
»

Summary of Contents for Grand Cherokee SRT8 2012





























































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands