manualshive.com logo in svg

Jeep Grand Cherokee SRT8 2012, Owner'S Manual

Share
Download
Jeep Grand Cherokee SRT8 2012 Owner'S Manual Download Page 246

Programming A Rolling Code

For programming garage door openers that were manu-
factured after 1995. These garage door openers can be
identified by the “LEARN” or “TRAIN” button located
where the hanging antenna is attached to the garage door
opener. It is NOT the button that is normally used to
open and close the door. The name and color of the
button may vary by manufacturer.

1. Turn the ignition switch to the ON/RUN position.

2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm)
away from the HomeLink

威

button you wish to program

while keeping the HomeLink

威

indicator light in view.

Training The Garage Door Opener

1 — Door Opener
2 — Training Button

244

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for Grand Cherokee SRT8 2012





























































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands