manualshive.com logo in svg

JDS Uniphase CellAdvisor JD780A Series, User Manual

Share
Download
JDS Uniphase CellAdvisor JD780A Series User Manual Download Page 494

JD780A Series Analyzers 

494

 

Using Cable and Antenna Analyzer 

Adjusting scale 

You can adjust the Y-axis scale to optimize the display of measurement trace(s). Adjusting scale does 
not affect the calibration state.

 

Procedure

 

1. 

Press the 

AMP/SCALE

 hard key. 

2. 

Do one of the following choices: 

–  

Press the 

Auto Scale

 to optimize the display of the measured trace by letting the 

instrument set the minimum and maximum values for the Y-axis automatically. 
Each time this key is pressed, the top and bottom scales are set to the minimum and 
maximum values with margin on the Y-axis of the chart. 

–  

Press the 

Full Scale

 to restore the insturment

’s default amplitude range for the Y-scale 

automatically. 

–  

To set the minimum and maximum values for the Y-axis manually, complete the following 
steps: 

a. 

Press the 

Maximum (Top)

 soft key. 

b. 

Enter a value by using the numeric keys. 

c. 

Press the 

Enter

 soft key. 

d. 

Press the 

Minimum (Top)

 soft key. 

e. 

Enter a value by using the numeric keys. 

f. 

Press the 

Enter

 soft key. 

 

 

NOTE

 

This setting is not used in the Smith Chart measurement mode. 

 

Setting sweep mode 

The default setting is 

Continue

 to sweep continuously for most on-going measurements. If you want to 

hold the measurement or get a single sweep, you can change the sweep mode. 
 

Procedure

 

To select the single sweep mode: 

1. 

Press the 

SWEEP

 hot key. 

2. 

Toggle the 

Sweep Mode

 soft key and select 

Single

. You can also use the 

HOLD

 hot key. 

The letter 

HOLD

 in red appears and the sweeping is paused. 

3. 

Optional

. Press the 

Sweep Once

 soft key to get a new measurement. 

 
To return to the continuous sweep mode: 

1. 

Toggle the 

Sweep Mode

 soft key and select 

Continue

. You can also use the 

HOLD

 hot key. 

The letter 

HOLD

 in red disappears and the sweeping resumes. 

 

Performing calibration 

To get reliable and accurate measurement results, you must perform a calibration on your instrument 
after setting frequencies and prior to making a measurement. To perform the calibration, you need to 
have the following ready: 
 

Summary of Contents for CellAdvisor JD780A Series

















































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands