background image

iVIZION® Banknote Validator

Operator’s Guide

June,  2014

June,  2014

Part No. 960-100932R_Rev. A

© 2014, JCM American, Corporation

1 6

1

Part No. 960-100932R_Rev. A

 For the Americas & Oceania, E-mail: [email protected]

For the UK, Ireland, Europe, Africa, Russia & Middle East, E-mail: [email protected] 

For Asia E-mail: [email protected]

JCM is a registered trademark of JCM American Corporation. All other product names 
mentioned herein may be registered trademarks or trademarks of their respective companies. 
Furthermore, 

®

 and 

©

 

are not always mentioned in each case throughout this publication.

Operator’s Guide

© 2014, JCM American, Corporation

Operator’s Guide

iVIZION

® 

Banknote Validator

Preventive Maintenance Instructions

This Guide describes procedures for the cleaning and maintenance of the 
iVIZION

®

 Banknote Validator. For additional information, refer to Section 2 of 

the iVIZION Operation and Maintenance Manual (JCM P/N 960-100929R).

iVIZION REFERENCE DIAGRAMS

Figure 1 identifies the iVIZION

 Validator Head, Transport Unit and Cash Box.

• Notes regarding iVIZION Components:

 –  Sensor locations are shown in yellow.
 –  Rollers are shown in blue.

 –  Drive Belts are shown in orange.
 –  Release levers are shown in green.
 –  Anti-stringing area is shown in red.

 Figure 1 

iVIZION Unit, Validator Head, Transport Unit and Cash Box

Typical iVIZION Components

iVIZION Validator Head

Typical iVIZION Unit 

(fully assembled)

iVIZION Head and Transport Unit

iVIZION Transport Unit 

(inverted)

iVIZION Cash Box

PERSONAL NOTES AND COMMENT AREA

Write any pertinent notes or comments regarding your particular installation 
here.

Summary of Contents for iVIZION









Reviews:

Related manuals for iVIZION