background image

3 - 1

Operating Safety

!

!

WARNING

Machine Condition

A defective machine can injure you or others. Do not operate
a machine which is defective or has missing parts. Make
sure the maintenance procedures in this manual are
completed before using the machine.

INT-2-1-2

!

!

WARNING

Controls

You or others can be killed or seriously injured if you operate
the control levers from outside the cab. Operate the control
levers only when you are correctly seated inside the cab.

INT-2-1-3

!

!

WARNING

Machine Limits

Operating the machine beyond its design limits can damage
the machine, it can also be dangerous. Do not operate the
machine outside its limits. Do not try to upgrade the
machine performance with unapproved modifications.

INT-2-1-4

!

!

WARNING

Engine/Steering Failure

If the engine or steering fails, stop the machine as quickly as
possible. Do not operate the machine until the fault has been
corrected.

INT-2-1-5

!

!

WARNING

Engine

The engine has rotating parts. Do not open the engine cover
while the engine is running. Do not use the machine with the
cover open.

INT-2-1-6

!

!

WARNING

Entering/Leaving

Entering the cab or canopy must only be made where steps
and handrails are provided. Always face the machine when
entering and leaving. Make sure the step(s), handrails and
your boot soles are clean and dry. Do not jump from the
machine. Do not use the machine controls as handholds,
use the handrails.

INT-2-1-7/1

!

!

WARNING

ROPS/FOPS Structure

The machine is fitted with a Roll Over Protection Structure
(ROPS) and a Falling Objects Protection Structure (FOPS).
You could be killed or seriously injured if you operate the
machine with a damaged or missing ROPS/FOPS. If the
ROPS/FOPS has been in an accident, do not use the
machine until the structure has been renewed. Modifications
and repairs that are not approved by the manufacturer may
be dangerous and will invalidate the ROPS/FOPS
certification.

INT-2-1-9/3

!

!

WARNING

Exhaust Gases

Breathing the machine exhaust gases can harm and
possibly kill you. Do not operate the machine in closed
spaces without making sure there is good ventilation. If
possible, fit an exhaust extension. If you begin to feel
drowsy, stop the machine at once. Get out of the cab into
fresh air.

INT-2-1-10

!

!

WARNING

Communications

Bad communications can cause accidents. Keep people
around you informed of what you will be doing. If you will be
working with other people, make sure any hand signals that
may be used are understood by everybody. Work sites can
be noisy, do not rely on spoken commands.

INT-2-2-3

!

!

WARNING

Ramps and Trailers

Water, mud, ice, grease and oil on ramps or trailers can
cause serious accidents. Make sure ramps and trailers are
clean before driving onto them. Use extreme caution when
driving onto ramps and trailers.

INT-2-2-6

!

!

DANGER

Sparks

Explosions and fire can be caused by sparks from the
exhaust or the electrical system. Do not use the machine in
closed areas where there is flammable material, vapour or
dust.

INT-2-2-10

Section 2

Care & Safety

9803/7110

Section 2

3 - 1

Issue 1

Summary of Contents for 2CX
































Reviews: