ENGLISH
USER MANUAL
JB SYSTEMS®
7/52
SPACE-COLOR Laser
DMX-CONFIGURATION OF SPACE-COLOR LASER:
CHANNEL
VALUE
DESCRIPTION
1
000-200
Stepper motor scanning speed (from fast to slow)
201-254
Space color laser is switched to stand-alone mode (use the AUTO/MUSIC
switch to put the laser in the desired mode)
255
Complete reset (to be used while switching from stand-alone to DMX mode)
2
000-014
Pattern 1
015-020
Pattern 2
023-027
Pattern 3
028-034
Pattern 4
035-041
Pattern 5
042-048
Pattern 6
049-055
Pattern 7
056-062
Pattern 8
063-070
Pattern 9
071-076
Pattern 10
077-083
Pattern 11
084-090
Pattern 12
091-097
Pattern 13
098-104
Pattern 14
105-111
Pattern 15
112-118
Pattern 16
119-125
Pattern 17
126-132
Pattern 18
133-140
Pattern 19
141-153
Pattern 20
154-160
Pattern 21
161-167
Pattern 22
168-174
Pattern 23
175-181
Pattern 24
182-188
Pattern 25
189-195
Pattern 26
196-202
Pattern 27
203-210
Pattern 28
211-216
Pattern 29
217-223
Pattern 30
224-230
Pattern 31
231-251
Pattern 32
252-255
Pattern 33
3
000-255
Rotation of the patterns
4
000-255
Zooming: pattern size (from small to big)
5
000-255
Panning movement (X-axis: left to right - value 128 is middle position)
6
000-255
Tilt movement (Y-axis: up and down - value 128 is middle position)
7
000
Blackout
001-254
Blanking frequency (from low to high)
255
No blanking
8
000-055
Beam color: Red
056-083
Beam color: Green
084-111
Beam color: Yellow
112-139
Beam color: Red & Green
140-167
Beam color: Yellow & Green
168-195
Beam color: Red & Yellow
196-254
Beam color: Red, Green & Yellow
255
Beam color: Original color of the pre-programmed patterns
ENGLISH
USER MANUAL
JB SYSTEMS®
8/52
SPACE-COLOR Laser
MAINTENANCE
Make sure the area below the installation place is free from unwanted persons during
servicing.
Switch off the unit, unplug the mains cable and wait until the unit has been cooled down.
During inspection the following points should be checked:
All screws used for installing the device and any of its parts should be tightly fastened
and may not be corroded.
Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally
free from any deformation.
When an optical lens is visibly damaged due to cracks or deep scratches, it must be
replaced.
The mains cables must be in impeccable condition and should be replaced immediately
when even a small problem is detected.
In order to protect the device from overheat the cooling fans (if any) and ventilation
openings should be cleaned monthly.
The interior of the device should be cleaned annually using a vacuum cleaner or air-jet.
The cleaning of internal and external optical lenses and/or mirrors must be carried out
periodically to optimize light output. Cleaning frequency depends on the environment in
which the fixture operates: damp, smoky or particularly dirty surroundings can cause
greater accumulation of dirt on the unit’s optics.
Clean with a soft cloth using normal glass cleaning products.
Always dry the parts carefully.
Clean the external optics at least once every 30 days.
Clean the internal optics at least every 90 days.
Attention: We strongly recommend internal cleaning to be carried out by qualified
personnel!
SPECIFICATIONS
Mains Input:
AC 230V, 50Hz
Fuse:
250V 1.5A slow blow (20mm glass)
Sound Control:
Internal microphone
DMX connections:
3pin XLR male / female
DMX channels:
8 channels
DMX starting address:
001
255
Laser Power:
30mW Green CW laser (
λ
= 532nm)
80mW Red CW laser (
λ
= 650nm)
Laser radiation class:
3B
Laser Safety Standard:
EN60825-1:1994 + A1:2002 + A2:2002
Size:
26 x 30x 10cm
Weight:
5,5kg
Every information is subject to change without prior notice
You can download the latest version of this user manual on our website: www.beglec.com
