![background image](http://html1.mh-extra.com/html/jayco/hummingbird-towables-2019/hummingbird-towables-2019_owners-manual_3586488079.webp)
Section 5: Slideout Systems
77
Power Gear Ram Slideout System
Typically used for Class C motorhomes.
Manual Override Procedure:
The system has been equipped with 3/4” hex override couplers located on the drive compo-
nent of the system. Due to the size and weight of some rooms, assistance may be needed to
push the room in.
Use the following steps to mechanically operate the room:
1.
Locate the ABS motor access cover for the slideout. This
cover will be located inside one of the storage compart-
ments under the slide room up at the top of the compart-
ment.
2.
Remove 4 screws holding the panel to the top of the com-
partment. Remove the cover.
3.
Unplug the motor leads at the connector. Gray connector
with red & black wires.
4.
To release the motor brake you must depress the spring
lock lever, which then allows you to pivot the brake lever,
which in turn releases the brake. These parts are located
inside the rubber boot wire tied over the motor. You must
manipulate these parts
without
removing the rubber boot.
As noted on the side-by-side photo, removing this boot
will void your motor warranty.
These photos will help
you figure out how this works. The side-by-side photo (be
-
low) shows the spring lock lever and the brake lever.
5.
The spring lock lever is a thin metal arm with a slight bend
at the end, which will hold the brake lever in the released
position.
6.
The brake lever is the heavier thicker metal arm with the
hole in the end.
7.
The normal position for these two levers is to be parallel
to each other as shown in the first side-by-side photo. The
motor brake is engaged with levers side by side.
8.
The brake lever is moveable; the spring lock lever is not
moveable. To release the brake lever, you must push the
bent end of the spring lock lever away from the brake le-
ver; this will allow you to pivot the brake lever so it moves
over on top of the spring lock lever. The bent end will
hold the brake lever in the released position. (photo shows
this “bend”).
9.
Once the brake motor is released, you will need to remove
the skirting on the side of the slideout floor where the hex
override is located.
10. Use a ratchet with a 3/4” socket (or wrench) to turn the
hex override and manually move the slideout.
11. When the slideout is retracted, check to make sure you have a good seal, and replace
the skirting on the slideout.
Table of Contents
Maintenance Record
Summary of Contents for Hummingbird Towables 2019
