![background image](http://html1.mh-extra.com/html/jayco/conventional-travel-trailer-2003/conventional-travel-trailer-2003_owners-manual_3492212044.webp)
77
76
If an energy source is available to the refrigerator, but is not operating correctly: A fault
code appears in the center display. The refrigerator controls try to change to a less
efficient energy source. If a less efficient energy source is not available, an audible alarm
sounds, and the refrigerator stops operation. Refer to the “Fault Codes” in the
manufacturer’s owner’s manual.
MANUAL MODE OPERATION
When you select one of the three manual modes, “AU” goes out in the center display and
either AC, LP, or DC appears. AC means that the refrigerator is operating on AC electric.
LP means that the refrigerator is operating on LP gas. DC means that the refrigerator is
operating on DC electric. If the energy source is interrupted, an audible alarm sounds,
and the refrigerator stops operation. Refer to the “Fault Codes” in the manufacturer’s
owner’s manual.
IGNITION OF LP GAS IN EITHER AUTO OR MANUAL MODE
NOTE
: On initial startup of the refrigerator, ignition of the LP gas may not occur
within 30 seconds.
If ignition of the LP gas does not occur with 30 seconds, the gas safety valve of the
refrigerator closes.
In the auto mode, the refrigerator control changes to a less efficient energy source (3-way
models only); the fault code “no” “FL” shows in the center display (2-way models only).
In the manual mode and operating on LP gas, an audible alarm starts, and the fault code
“no” “FL” shows in the center display. The audible alarm and the fault code remain until
you push the MODE button. Push the ON/OFF button two times to stop and start the
refrigerator.
If ignition does not occur after two or three times, check the LP gas supply line; consult
your local dealer or an authorized Norcold Serivice Center; change to manual mode and
operate on AC electric, or DC electric (3-way models only).
Ice Maker
Ice maker is assembled to the refrigerators at the factory as optional equipment. If the
refrigerator does not have a factory installed ice maker, one can not be added to the
refrigerator at a later time.
ICE MAKER OPERATION
1.
Open the water shut off valve of the vehicle.
NOTE
:
Make sure that the ice maker arm can move freely and does not touch the
frozen foods in the freezer
2.
Push the ice maker arm down to the ON position.
1
CAUTION: If you operate the refrigerator without connecting the water
supply line and/or opening the water shut off valve of the vehicle, make sure
the ice maker arm is up in the OFF position.
3.
Allow the freezer to cool to 32° F (0° C) (a minimum of 24 hours) and ice
production will begin to fill the storage bin.
NOTE
: New plumbing connections and/or impurities in the water supply line after
winterizing can cause the first ice to be discolored or have an odd flavor.
4.
To stop the ice maker, push the ice maker arm up to the OFF position.
IGNITION OF LP GAS IN EITHER AUTO OR MANUAL MODE
Note: On initial startup of the refrigerator, ignition of the LP gas may not occur within 30
seconds.
If ignition of the LP gas does not occur with 30 seconds, the gas safety valve of the
refrigerator closes, and the refrigerator stops operation. Refer to the “Fault Codes” in the
manufacturer’s owner’s manual. The fault code remains until you push the ON/OFF
button two times (to stop and start the refrigerator). If ignition does not occur after two or
three times, check the LP gas supply line; consult your local dealer or an authorized
Norcold Serivice Center; change to manual mode and operate on AC electric.
Operating the Refrigerator Controls – N841
CONTROL PANEL
The refrigerator control panel is between the freezer compartment and the fresh food
compartment. To maintain the operating control functions of the refrigerator, a 12 volt
DC power supply is necessary. The refrigerator and any other DC components in the
vehicle receive DC power from the 12 volt system of the vehicle; either an auxillary
battery, a converter, or the vehicle engine battery.
The ON/OFF button (1) starts and shuts down the refrigerator. If the refrigerator is shut
down, press the ON/OFF button to start the refrigerator in auto mode. If the refrigerator
is operating, press and hold the ON/OFF button for two seconds to shut down the
refrigerator.
The TEMP SET button (3) controls the temperature adjustment of the freezer and the
fresh food compartment. The temperature adjustment that you select does not change if
the operation mode of the refrigerator changes. Press the TEMP SET button and the
temperature setting “1-9” appears in the center display (4). Push and hold the TEMP SET
button and the temperature setting changes. The number “9” is the coldest temperature
setting.
The MODE button (2) controls the operation mode of the refigerator. Push and hold the
MODE button and each of the four operating modes of the refrigerator flash one at a time
in the center display. There is one automatic mode of operation, and three manual modes
of operation. When the mode of operation that you wish shows in the center display,
release the MODE button.
AUTOMATIC MODE OPERATION
When you select AUTO mode, the refrigerator controls automatically select the most
efficient energy source that is available for operation. If a more efficient energy source
becomes available, the refrigerator controls change from the current energy source to the
more efficient energy source.
Fig. 5-13
NORCOLD
ON
1 - COLD COLDEST - 9
TEMP
SET
MODE
ON-OFF
2
3
1
4
Summary of Contents for Conventional Travel Trailer 2003
Page 9: ...7 6 CHAPTER 2 OBTAINING SERVICE WARRANTY REGISTRATION SAM PLE SAM PLE ...
Page 61: ...111 110 NOTES SAM PLE ...
Page 62: ...113 112 NOTES NOTES ...
Page 63: ...114 NOTES ...