Jatco RE4F04B Manual Download Page 275

Page: 275 / 708

REMOVAL AND INSTALLATION

AT-275

[RE4F04B]

Revision: November 2006

2006 Altima

REMOVAL AND INSTALLATION

PFP:00000

Removal

ECS009AU

Remove battery and bracket.

Remove air cleaner assembly. Refer to

EM-17, "Removal and Installation"

Disconnect terminal cord assembly harness connector and park/neutral position (PNP) switch harness
connectors.

Disconnect the following connectors:

●

terminal cord assembly

●

park/neutral position (PNP) switch

●

revolution sensor

●

vehicle speed sensor

●

mass air flow sensor

●

turbine revolution sensor

●

ground

Remove LH mounting bracket from transaxle and body.

Disconnect control cable at transaxle side.

Remove drive shafts. Refer to

FAX-11, "FRONT DRIVE SHAFT"

Drain ATF from transaxle. Refer to

AT-398, "Changing A/T Fluid"

Remove push clips and engine undercover.

10. Disconnect fluid cooler piping.

11. Remove starter motor from transaxle. Refer to

SC-15, "Removal

and Installation"

12. Support engine.

13. Remove upper transaxle to engine bolts.

14. Remove front suspension member. Refer to

FSU-15, "Removal and Installation"

15. Remove rear cover plate and torque converter to drive plate

bolts.

NOTE:
Rotate crankshaft for access to torque convertor bolts.

16. Support transaxle with a jack.

17. Remove lower transaxle to engine bolts.

18. Lower transaxle while supporting it with a jack.

LCIA0086E

WCIA0069E

Summary of Contents for RE4F04B





































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for RE4F04B

Reviews:

Related manuals for RE4F04B

Brands by name

Popular brands

Jatco RE4F04B, Manual

Search results

Summary of Contents for RE4F04B

Reviews:

Related manuals for RE4F04B

Brands by name

Popular brands