manualshive.com logo in svg

Jatco RE4F04B, Manual

Share
Download
Jatco RE4F04B Manual Download Page 201

DTC VEHICLE SPEED SENSOR MTR

AT-201

[RE4F04B]

D

E

F

G

H

I

J

K

L

M

A

B

AT

Revision: November 2006

2006 Altima

DTC VEHICLE SPEED SENSOR MTR

PFP:24814

Description

ECS0099C

The vehicle speed sensor·MTR is built into the speedometer assem-
bly. The sensor functions as an auxiliary device to the revolution sen-
sor when it is malfunctioning. The TCM will then use a signal sent
from the vehicle speed sensor·MTR.

On Board Diagnosis Logic

ECS0099D

Diagnostic trouble code VHCL SPEED SEN·MTR with CONSULT-II or 2nd judgement flicker without CON-
SULT-II is detected when TCM does not receive the proper voltage signal from the sensor.

Possible Cause

ECS0099E

Check the following items.

●

Harness or connectors
(The sensor circuit is open or shorted.)

●

Vehicle speed sensor

Diagnostic Trouble Code (DTC) Confirmation Procedure

ECS0099F

CAUTION:

●

Always drive vehicle at a safe speed.

●

If conducting this “DTC Confirmation Procedure” again, always turn ignition switch OFF and wait
at least 10 seconds before continuing.

After the repair, perform the following procedure to confirm the malfunction is eliminated.

WITH CONSULT-II

1.

Turn ignition switch ON and select “DATA MONITOR” mode for
“A/T” with CONSULT-II.

2.

Start engine and accelerate vehicle from 0 to 25 km/h (0 to 16
MPH).

WITHOUT CONSULT-II

1.

Start engine.

WCIA0556E

BCIA0030E

BCIA0031E

Summary of Contents for RE4F04B





































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands