Jatco RE4F04B Manual Download Page 110 | Manualshive

Page: 110 / 708

background image

AT-110

[RE4F04B]

DTC P0705 PARK/NEUTRAL POSITION SWITCH

Revision: November 2006

2006 Altima

DTC P0705 PARK/NEUTRAL POSITION SWITCH

PFP:32006

Description

ECS0096I

●

The park/neutral position (PNP) switch includes a transaxle
range switch.

●

The transaxle range switch detects the selector lever position
and sends a signal to the TCM.

On Board Diagnosis Logic

ECS0096J

Diagnostic trouble code PNP SW/CIRC with CONSULT-II or P0705 without CONSULT-II is detected when
TCM does not receive the correct voltage signal from the switch based on the gear position.

Possible Cause

ECS0096K

Check the following items.

●

Harness or connectors
(The park/neutral position (PNP) switch circuit is open or shorted.)

●

Park/neutral position (PNP) switch

Diagnostic Trouble Code (DTC) Confirmation Procedure

ECS0096L

CAUTION:

Always drive vehicle at a safe speed.
NOTE:
If “DTC Confirmation Procedure” has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.

WITH CONSULT-II

1.

Turn ignition switch ON.

2.

Select “DATA MONITOR” mode for “A/T” with CONSULT-II.

3.

Start engine and maintain the following conditions for at least 5
consecutive seconds.
VHCL SPEED SE: 10 km/h (6 MPH) or more
THRTL POS SEN: More than 1.3V
Selector lever: 3 or D position

WCIA0066E

BCIA0030E

BCIA0031E

«
...
108
109
110
111
112
...
»

Summary of Contents for RE4F04B





































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RE4F04B

Passport 500 Pro

Brand: Fender Pages: 4

Brand: Karel Pages: 43

Brand: Nady Systems Pages: 2

HOMESTREAM HS-USB-MIC

Brand: Ikan Pages: 14

Brand: Samson Pages: 36

Brand: RCA Pages: 2

RS2181i/RS2181iF

Brand: RCA Pages: 1

RS2052 - Compact Bookshelf System

Brand: RCA Pages: 20

Brand: RCA Pages: 26

Brand: JVC Pages: 19

Brand: JVC Pages: 36

Brand: JVC Pages: 2

2-661-374-11(4)

Brand: Sony Pages: 40

Brand: Sony Pages: 92

3-097-194-15(1)

Brand: Sony Pages: 112

Brand: Earthworks Audio Pages: 3

Brand: Earthworks Audio Pages: 4

Brand: Earthworks Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands