Janome HF2022 Service Manual Download | Manualshive

Page: 20 / 27

background image

MECHANICAL ADJUSTMENT

BUTTON HOLE FEED BARANCE

CORRECT SETTING
WHEN SEWING BUTTONHOLE, THE STITCHES ON EACH SIDE OF BUTTONHOLE SHOULD BE
THE SAME STITCH DENSITY.
THE RANGE OF 9 - 11 STITCHES IN THE RIGHT SIDE ROW “BACKWARD FEEDING” AGAINST 10
STITCHES IN THE LEFT SIDE ROW “FORWARD FEEDING” IS CONSIDERED ACCEPTABLE.

TO ADJUST
1.

CONFIRM THE STITCHES BY SEWING BUTTONHOLES, AND REMOVE THE CAP.

2.

TURN THE ADJUSTING SCREW IN THE DIRECTION OF C IN CASE OF A (RIGHT STITCHES
ARE ROUGH), OR IN THE DIRECTION OF D IN CASE OF B (LEFT STITCHES ARE ROUGH).

3.

MOUNT THE CAP.
* IN CASE OF MODEL 1541 HAVING ONE STEP BUTTONHOLE FUNCTION, THE
“FORWARD FEEDING” AND “BACKWARD FEEDING” ARE REVERSED.

CAP

NOTCH

ADJUSTING SCREW

BACKWARD FEEDING

FORWARD FEEDING

18

«
...
18
19
20
21
22
...
»

Summary of Contents for HF2022




























Reviews:

No comments

Related manuals for HF2022

Brand: Panasonic Pages: 88

GBC StreamPunch Ultra

Brand: ACCO Brands Pages: 92

Brand: afx light Pages: 19

Brand: GBC Pages: 10

Pro-Stitcher BLPS3

Brand: Baby Lock Pages: 105

KING COBRA 1200 PRO

Brand: U.S. Products Pages: 12

Brand: Kettler Pages: 36

Brand: Muratec Pages: 138

Brand: JUKI Pages: 20

Brand: JUKI Pages: 28

Brand: JUKI Pages: 52

Brand: JUKI Pages: 164

Brand: JUKI Pages: 60

HZL - 353Z Series

Brand: JUKI Pages: 35

Innov-is NV1800Q

Brand: Brother Pages: 32

Brand: Brother Pages: 40

Brand: Brother Pages: 28

Innov-is NV1300

Brand: Brother Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands