J&M 275-ST Page 37 Operator'S Manual Download

Page: 37 / 58

4.0 Wiring

Wireless Remote (optional)

Starts/Stops Motor

Raises/Lowers Conveyer

Opens/Closes Tank Doors

Hydraulic Conveyer Swing

Electronic Auto Scale Shutoff

Toggle Switch

Ground

Wireless Receiver

Controllers/Remotes

Item # Description

Part #

Qty.

Handheld Controller 1

JM0014991

Wireless Remote w/ Receiver

JM0015005

JM0036049

JM0036050

BOOM

SWING

FRONT

REAR

CONVEYOR

START

STOP

FRONT

DOOR

DOWN

REAR

DOOR

DOWN

BOOM

DOWN

Description

N/C

Conveyor Swing Front

Conveyor Swing Rear

Boom Up

Boom Down

Rear Door Up

Front Door Down

Red - Power

Front Door Up

Rear Door Down

Dump

Conveyor Start

N/C

Handheld Controller

Starts/Stops Motor

Raises/Lowers Conveyer

Opens/Closes Tank Doors

Hydraulic Conveyer Swing

JM0014991

JM0031012

Stationary Control

Raises/Lowers Conveyer

Opens/Closes Tank Doors

Hydraulic Conveyer Swing

On/Off Talc

Talc Speed

On/Off Conveyor

On/Off Lights

4.1 Remote Options

TARE

SCROLL

NAVIGATION

DISP.

AUTO

OPEN

CLOSE

FRONT

DOOR

OPEN

CLOSE

REAR

DOOR

CONVEYOR

FRONT

REAR

CONV

START

CONV

STOP

POWER

In order for the Auto Dispense function to work, the Speed Tender must

be equipped with a factory installed and powered on Weigh-Tronix 640XL

scale indicator with the J&M Mega Remote with Auto Dispense as shown

to the right.

J&M Mega Remote

with Auto Dispense

Note: For best accuracy,

RUN THROTTLE AT 80% OR HIGHER

J&M Manufacturing Co., Inc. - Fort Recovery, Ohio - 419.375.2376 - www.jm-inc.com

Auto Dispense

Instruction

J&M Mega Remote

For use with the Weigh-Tronix 640XL scale package

and J&M Mega Remote Control Installed

Please consult your operators manual

for more detailed information

Pairing the J&M Mega Remote to the

Receiver

Note: The wireless switch should be in the off position

• Hold Power until the screen displays TEACHING MODE

• Toggle the Wireless Power Switch to On

• The Display will now display “TEACHING COMPLETE” and will return to the live weight display.

Using the Auto Dispense Feature

Note: The Auto Dispense Feature is only active after you change or

confirm the weight and/or door settings each time the reciever is turned on

• Simply press the

Green

Auto Dispense button to activate

the feature.

• The system will Start the conveyor, open the door, unload within

2-4 Lbs of the desire weight, close the door and cleanout the

conveyor with a single press of a button.

• If filling multiple planter boxes, press the Auto Dispense button again

to repeat the process.

This can be done during the conveyor cleanout stage

Selecting the Door to Auto Dispense

•

Press Scroll twice to enter the Door Selection menu

• Hold Tare until Door Number is flashing

• Use the Up and Down Navigation buttons to select either door 1 or 2

Door 1 = Front Door

Door 2 = Rear Door

• Hold Tare to Save to door setting

Setting the desired Auto Dispense Weight

• Press Scroll to enter Auto Dispense menu

• Hold Tare till weight flashes

• Use the Left and Right Navigation buttons to select the digit and

the Up and Down buttons to change the digit

• Hold Tare to Save the desire weight

J&M

MEGA REMOTE

JM0028114

DPST (On-Off)

Conveyor Start/Stop

(This is a throw switch, it is either

on or off.)

JM0037124

DPDT (On-Off-On)

Boom Swing Front/Rear

Front Door Up/Down

Rear Door Up/Down

Boom Up/Down

(Three position switch)

JM0037125

DPDT (On-On)

Conveyor Start/Stop

(This is a momentary switch, once you

let go of the switch it will turn off.)

Note: If replacing Conveyor

Start/Stop switch, both

JM0028114 & JM0037125

will work. If operator wants

the switch to be on and off then

select JM0028114. If operator

wants the coveyor to only run

while he is holding the switch

then select JM0037125.

Summary of Contents for 275-ST



























































Search results

Summary of Contents for 275-ST

Reviews:

Related manuals for 275-ST

Brands by name

Popular brands

J&M 275-ST, Operator'S Manual

Search results

Summary of Contents for 275-ST

Reviews:

Related manuals for 275-ST

Brands by name

Popular brands