MP3
PLAYER
/
RECEIVER
USB
/
SD
/
MMC
/
AUX
SLOT
INSTALLATION
PRECAUTIONS
Choose the mounting location where the unit will not interfere with the normal
the driver.
driving function of
Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up
properly and the unit and the system work properly.
Use only the parts included with the unit to ensure proper installation. The use of unauthorized
parts can cause malfunctions.
Consult with your nearest dealer if installation requires the drilling of holes or other modifications of
the vehicle.
Install the unit where it does not get in the driver's way and cannot injure the passenger if there is
a sudden stop. Like an emergency stop.
Avoid installing the unit where it would be subject to high temperature, such as from direct
sunlight, or from hot air, form the heater, or where it would be subject to dust, dirt or excessive
vibration.
INSTALLATION
GENERAL
OPERATIONS
FRONT PANEL LAYOUT
03
5
21
20
18
18
17
1
2
3
15
8
7
9
12
14
6
19
4
10
13
11
Power
/
MOD
Button
Volume/Sel
Button
Display/Mute
Button
LCD
Display
Reset
Button
Band
switch/ID3 select
Tune
Seek
&
Track
forward
Button
Tune
Seek
&
Track
reverse
Button
Automatically
memory
storing
Play/pause
&
Preset
Button
1
Intro
&
Preset
Button
2
Repeat
&
Preset
Button
3
Random
&
Preset
Button
4
Preset
Button
5
Preset
Button
6
Release Button
Remote
Control
sensor
AUX
IN
JACK
USB
connecter
21
20
19
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
18
SD/MMC
slot
Flashing LED
16
GENERAL
OPERATIONS
EQ OFF/ON
Select “EQ ON ” POP CLASS ROCK EQ OFF menu male.
GENERAL OPERATIONS
SOUND ADJUSTMENT
Turn on (2) can adjust the desired volume quality.
Press SEL button (2) will change in the following order.
Option:
VOLUME
Adjust volume level by using
(2)
knob
.
Turn the VOL knob to left to decrease
the sound level, turn the VOL knob to right to increase the sound level.
VOL
/
SEL
Note: The unit is initially set to volume mode.
VOL
BAS
TRE
BAL
FAD
(
Volume
)
(
Bass
)
(
Treble
) (
Balance
)
(
Fader
)
Press VOL/SEL button shortly and turn VOL button to right or left to select different
mode.
menu
BASS
Press VOL
/
SEL button(2) one time. Adjust bass level by using
VOL
/
SEL(2)
Knob
.
TREBLE
Press VOL
/
SEL button(2) two times. Adjust treble level by using VOL
/
SEL(2) Knob .
BALANCE
Press VOL
/
SEL button(2) three times. Adjust sound balance between left and right
speakers by using
VOL
/
SEL(2)Knob
.
FADER (optional)
Press SEL button(2) four times. Adjust sound balance between front and rear speakers
by using VOL
/
SEL(2)Knob.
SELECT
MENU
Press VOL/SEL button for several seconds, selecting menu is activated as cyclical mode
of following function for use's selection:
BAS
VOL
TRE BAL
EQ
LOUD OFF/ON
STEREO/MONO
DX/LOC
FAD
04
POWER /MOD conversion
2
.
Under power off status,short press is power on,
Under power on status,short press is switching mode,long press is power off.
LOUD
EQ
02
DIN FRONT-MOUNT (Method A)
1.Frame
2. Insert fingers into the groove in the front of frame and pull out to remove t he frame.
(When
reattaching the frame,point
the side with a groove downwards and attach It.)
3
.
Lever
Insert the levers supplied with the unit into the grooves at both sides of the unit and shown in
figure until they click. Pulling the levers makes possible to remove the unit from the dashboard.
2
1
3
Removing
the
unit
Fastening the unit to the factory radio mounting bracket
:
1. Select a position where the screw holes of the bracket and the screw holes of the main unit
become aligned (are fitted), and tighten the screws at 2 places on each side. Use either truss
screws (5 x 5mm) .
2. Screw
3. Dashboard or Console.
DIN REAR-MOUNT (Method B)
Installation using the screw holes on the sides of the unit.
3
2
2
INPUT
THE
SD
CARD
The
SD
oblique
angle
keeps Rightward exposure
,
put
into the
SD
slot
and
press
it
again to
eject.
3 / RPT
6 /+10
BAND
AMS
AUX
MODE
DISP/
JS-8500
3 / RPT
1/
5 /-10
4 / RDM
2 / INT
6 /+10
BAND
AMS
AUX
/ MODE
DISP/
3 / RPT
1/
5 /-10
4 / RDM
2 / INT
6 /+10
BAND
AMS
AUX
/ MODE
DISP/
