9
4.4 Programming Filter Cycles (2011-2012 J200 models equipped with a circulation
pump)
To select a pre-programmed filter cycle or lockout mode, press and hold both control panel
WARMER and COOLER buttons
at the same time
, then release. Then press either WARMER or
COOLER buttons to select either filter mode F0 through L2 below:
Standard Mode
F0
5 minutes of filtration per day (one 5 minute “Blow-Out” cycle every 24 hours to purge all plumbing lines.
F1
1 hour of filtration per day (one 30-minute cycle every 12 hours); this is the factory default setting.
F2
1.5 hours of filtration per day (one 30-minute cycle every 8 hours).
F3
2 hours of filtration per day (one 30-minute cycle every 6 hours).
Economy Mode
F4
1 hour of filtration/heating per day (one 30-minute cycle every 12 hours).
F5
1.5 hours of filtration/heating per day (one 30-minute cycle every 8 hours).
F6
2 hours of filtration/heating per day (one 30-minute cycle every 6 hours).
Lock Mode
L1
Lock Out (disables all hot tub functions to permit filter cleaning) - If hot tub is heating when the system is
put into lockout mode, the heater will immediately turn off and the pump will cycle water for 30 seconds to
cool heater element, then turn off.
L2
Lock Mode (disables the jets and light buttons to prevent unauthorized use of the hot tub) - filter cycles and
heater will continue to operation as programmed in this mode. The temperature display flashes when this
function is enabled.
Example: The “F3” filter cycle was enabled prior to choosing lock mode. The hot tub
continues to perform filter cycle “F3” until lock mode is canceled, allowing another filter cycle to be selected.
4.5 Programming Filter Cycles (2013+ J200 models not equipped with a circulation
pump)
To select a pre-programmed filter cycle or lockout mode, press and hold both control panel
WARMER and COOLER buttons
at the same time
, then release. Then press either WARMER or
COOLER buttons to select either filter mode F1 through L2 below:
Standard Mode
F1
4 hours of filtration a day (2 hour cycle every 12 hours): this is the factory default setting.
F2
6 hours of filtration a day (2 hour cycle every 8 hours)
F3
8 hours of filtration a day (2 hour cycle every 6 hours)
Economy Mode
F4
4 hours of filtration a day (2 hour cycle every 12 hours)
F5
6 hours of filtration a day (2 hour cycle every 8 hours)
F6
8 hours of filtration a day (2 hour cycle every 6 hours)
Lock Mode
L1
Lock Out (disables all hot tub functions to permit filter cleaning).
Note:
The spa should not be left in this lock mode for an extended period of time. Especially in colder climates
or when freezing conditions exist.
L2
Lock Mode (disables the jets buttons to prevent unauthorized use of the hot tub) filtration/heating cycles
and heater will continue to operation as programmed in this mode. The temperature display flashes
when this function is enabled.
Example: The “F3” filter cycle was enabled prior to choosing lock mode.
The hot tub continues to perform filter cycle “F3” until lock mode is canceled, allowing another filter
cycle to be selected.
L3*
Lock Mode (disables the temperature up and down buttons to prevent unauthorized temperature
adjustments). Filtration/heating cycle will continue to operate as programmed in this mode. The jets and
lights buttons will still continue to operate as normal. The temperature display flashes when this function
is enabled. *Due to a difference in software this feature is not available for all models, started in 2014.
Note:
To exit a Lock Mode you will need to re-enter the filtration/heating modes and select a cycle from F0-F6.
