background image

 

 

 

Page 4 of 32 

 

IS2303VSP3J  Rev-A 

Basic safety precautions should always be followed, including the following: Failure to follow instructions may result in injury. 

 This is the safety-alert symbol.  When you see this symbol on your pump or in this manual, look for one of the following 

signal words, and be alert to the potential for personal injury. 

 

WARNING

 

warns about hazards that 

could

 cause serious personal injury, death or major property damage 

and if ignored presents a potential hazard. 

 

CAUTION

 warns about hazards that 

will

 or 

can

 cause minor or moderate personal injury and/or property 

damage and if ignored presents a potential hazard.  It can also make consumers aware of actions that are unpredictable and 
unsafe.   
The 

NOTICE

 label indicates special instructions that are important but not related to hazards. 

 

1.

 

IMPORTANT SAFETY INSTRUCTIONS 

Before installing or servicing this electrical equipment, turn power supply OFF. 

 

 

 

WARNING

 

– 

READ AND FOLLOW ALL INSTRUCTIONS

 in 

this owner’s manual and on the equipment.  Failure to follow instructions can cause severe injury and/or death. 

 

WARNING

 – This product should be installed and serviced only by a qualified professional. 

 

CAUTION

 – All electrical wiring MUST be in conformance with all applicable local codes, regulations, and the 

National Electric Code (NEC). 

 

ATTENTION INSTALLER - THIS MANUAL CONTAINS IMPORTANT INFORMATION ABOUT THE 
INSTALLATION, OPERATION, AND SAFE USE OF THIS VARIABLE SPEED PUMP THAT MUST BE 
FURNISHED TO THE END USER OF THIS PRODUCT.  FAILURE TO READ AND FOLLOW ALL 
INSTRUCTIONS COULD RESULT IN SERIOUS INJURY. 

 

 

 

WARNING

 – To reduce risk of injury, do not permit children to use or climb on this product.  Closely 

supervise children at all times.  Components such as the filtration system, pumps, and heaters must be positioned to 
prevent children from using them as a means of access to the pool. 

 

CAUTION

 – This pump is intended for use on permanently installed swimming pools and may also be used 

with hot tubs and spas if so marked.  Do NOT use with storable pools.  A permanently installed pool is constructed in or 
on the ground or in a building such that it cannot be readily disassembled for storage.  A storable pool is constructed so 
that it is capable of being readily disassembled for storage and reassembled to its original integrity.  Though this product is 
designed for outdoor use, it is strongly advised to protect the electrical components from the weather.  Select a well-
drained area, one that will not flood when it rains.  It requires free circulation of air for cooling.  Do not install in a damp or 
non-ventilated location.  If installed within an outer enclosure or beneath the skirt of a hot tub or spa, adequate ventilation 
and free circulation of air must be provided to prevent overheating of the motor. 

 

 

 

Summary of Contents for JVS165S

































Reviews: