background image

Model 18590-Series

Model: 18590-Series

SELF-PRIMING
MACERATOR PUMP

FEATURES

Pump:

Self-Priming Flexible Impeller with
Stainless Steel Wearplate

Impeller: 

Jabsco Nitrile compound

Macerator:

Stainless Steel Cutter reduces particle
size to 1/8" (3mm) maximum

Seal:

Lip Type

Ports:

Inlet - 1-1/2" (38mm)Hose Barb 
and 1-1/2" N.P.T. (Male)
Outlet - 1" (19mm) Hose Barb

Motor:

Permanent Magnet Type, Fully
Enclosed, with Stainless Steel Shaft
Complies with USCG Regulation 183.410
and ISO 8846 MARINE for Ignition
Protection

Weight:

5 lb (2,3 kg) Approx.

VARIATIONS AVAILABLE

MODEL NO.

DESCRIPTION

18590-0000

12 Volt

18590-0090 

12 Volt EMC

18590-0001 

24 Volt

18590-0091 

24 Volt EMC

APPLICATION

The JABSCO 18590 series dc macerator pump unit is the
ideal solution for emptying marine holding tanks when not
in a discharge restricted area. The JABSCO macerator is
self-priming to a five foot lift when impeller is wet, four foot
when dry, and may be mounted in any convenient point in
the waste discharge system. The macerator section grinds
waste down to a particle size of 1/8" (3mm) maximum so it
can easily by pumped through a 1" (19mm) ID discharge
hose. The pump section is self-priming, permitting the unit
to be mounted above the tank in a convenient location.
(For optimal efficiency, locate pump as close to holding
tank as possible.)

The macerator has an approximate flow rate of 12 GPM
(45 LPM) and will empty a typical 30 gallon (115 litre) hold-
ing tank in less than 3 minutes.

The 18590 series waste pump will macerate and pump all
waste and tissue normally found in marine and recreational
vehicle waste systems. 

Motors meet USCG Electrical Regulation Title
33, Chapter 1, Part 183; Subpart 1 and ISO
8846 MARINE for IGNITION PROTECTION.

OPERATING INSTRUCTIONS

The macerator should be controlled by a momentary
switch (push and hold) positioned close enough to the
pump so it can be heard while operating. When the tank is
empty there will be a change in pump noise (louder, high-
er frequency) at which time the macerator should immedi-
ately be switched off.

The macerator pump unit has been designed to handle
waste, toilet tissue, and facial tissue. It will also handle

solids such as cigarettes,
cigars and chunks of soft
fruits or vegetables less
than 1" size. It will not
pump solid objects like
fruit pits, rags, wet
strength kitchen towels,
tampons or sanitary nap-
kins. The holding tank and
pump should be flushed
with several gallons of
water after each pumpout.
Do NOT run pump dry

longer than 30 seconds or impeller and pump damage
may result. Make sure the battery is ful!y charged. The dc
motor is suitable only for intermittent duty and should not
be run for more than 15 minutes continuously. At maxi-
mum flow of 12 GPM (45 LPM) the macerator can empty
a 180 gallon (680 litre) holding tank in a single operation.

The pumps should be used in accordance with EPA,
USCG Marine Sanitation Regulations, and any regional
or local ordinances.

Summary of Contents for 18590 Series

Page 1: ...12 GPM 45 LPM and will empty a typical 30 gallon 115 litre hold ing tank in less than 3 minutes The 18590 series waste pump will macerate and pump all waste and tissue normally found in marine and recreational vehicle waste systems Motors meet USCG Electrical Regulation Title 33 Chapter 1 Part 183 Subpart 1 and ISO 8846 MARINE for IGNITION PROTECTION OPERATING INSTRUCTIONS The macerator should be ...

Page 2: ...9mm ID hose for discharge and connect to thru hull fitting located approximately 4 6 inches above waterline NOTICE The discharge thru hull may be positioned below the waterline only if the discharge hose has a vented loop fit ting installed at least 8 above the waterline at all angles of heel or trim Consult with a qualified marine plumber Teflon is a registered trademark of E I DuPont de Nemours ...

Page 3: ... chopper to the shaft with the locknut Position the macerator housing on the four studs ensuring the cut out in the inner wall aligns with pump body inlet port and hole in the wearplate Position a new fiber washer on each of the studs and secure the macerator housing in place with the four acorn nuts PARTS LIST PART KEY DESCRIPTION NUMBER QTY 1 Acorn Nut 91085 0340 4 2 Fiber Washer 91613 0140 4 3 ...

Page 4: ...22 Tel 045 475 8906 Fax 045 475 8908 GERMANY Jabsco GmbH Oststrasse 28 22840 Norderstedt Tel 49 40 53 53 73 0 Fax 49 40 53 53 73 11 THE PRODUCTS DESCRIBED HEREIN ARE SUBJECT TO THE JABSCO ONE YEAR LIMITED WARRANTY WHICH IS AVAILABLE FOR YOUR INSPECTION UPON REQUEST Copyright 2003 ITT Industries Printed in U S A All Rights Reserved Form 43000 0005 Rev 3 2003 4 23 32 120 2 5 8 67 3 5 8 92 3 4 19 2 1...

Reviews: