J.P. Instruments EDM-760 TWIN Pilot'S Manual Download Page 37 | Manualshive

Page: 37 / 69

background image

in the digital display in either the Automatic or Manual
indexing modes or during the pilot programming procedure.



In the

FF

(

F

uel Flow)

position only fuel flow measurements

are displayed in the digital display in either the Automatic or
Manual indexing modes or during the pilot programming
procedure.



In the

ALL

(

A

ll

) position, the EDM-760/790 both installed

temperature and fuel flow measurements are displayed in the
digital display in either the Automatic or Manual indexing
modes or during the

pilot

procedure.

Start Up Fuel

After initial self-test, you will be asked to inform the EDM-760/790 of
start up fuel. The EDM-760/790 will display

FUEL

for one second, and

then flash

FILL? N

until any button is pressed. If your aircraft has tank

fill tabs and no auxiliary tanks, you can use the auxiliary tank feature to
select either filling to the tank tabs or topping the tank. See “Main Tank
Capacity” and “Auxiliary Tanks” beginning on page 31 to program the
EDM-760/790 for this feature. The EDM-760/790 does not differentiate
fuel flow between the main and auxiliary tanks; it considers only

total

fuel

in the aircraft.

During flight you may also inform the EDM-760/790 of

startup fuel using the pilot program mode, page 39, if you forgot to do
so at start up.

main tank

auxiliary tank

main tank with tab

tab

Auxiliary capacity

Main capacity

Refer to the column in the chart below corresponding to your fuel tank
configuration. Tap the

LF

button to select one of the four following

fueling choices on the left column of the chart.

LF to
choose



Main tanks only, no

tabs

Main tanks

with tabs

Main & Auxiliary

tanks

FILL?

N

Did not add any fuel since last shutdown.

FILL

Topped the main

Filled only

Topped the main tanks.

For Your Safe Flight

Page 31

«
...
35
36
37
38
39
...
»

Summary of Contents for EDM-760 TWIN






































































Reviews:

No comments

Related manuals for EDM-760 TWIN

Brand: Flybox Pages: 72

Hot Food Display Cabinets CHS/1N

Brand: BKI Pages: 12

Brand: Bartscher Pages: 27

Brand: Lamp Pages: 4

Brand: Costan Pages: 52

Brand: SIFA Pages: 92

Harmony HMG2642R.4439

Brand: Structural Concepts Pages: 26

Brand: Structural Concepts Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands