iWave Zynq-7000 SoC Hardware User'S Manual Download Page 57

Page: 57 / 58

REL1.0

Page 57 of 58

iWave Systems Technologies Pvt. Ltd.

Zynq-7000 SoC SODIMM Development Platform Hardware User Guide

ORDERING INFORMATION

The below table provides the standard orderable part numbers for Zynq-7000 SoC SODIMM Development platform

which includes Zynq-7000 SoC SODIMM SOM and SODIMM carrier board.

Table 11: Orderable Product Part Numbers

Product Part Number

Description

Temperature

iW-G28D-SM20-3D512M-E008G-LCA

With Zynq 7020 SOC (-1), 512MB DDR3, 8GB eMMC
Flash, Wi-Fi/BT kit with Linux

Commercial

iW-G28D-SM07-3D512M-E008G-LCA

With Zynq 7007S SOC (-1), 512MB DDR3, 8GB eMMC
Flash, Wi-Fi/BT kit with Linux

Commercial

Important Note:

Please contact iWave for orderable part number of higher density/ higher speed grade/ higher

memory size supported Zynq-7000 SoC SODIMM SOM based DevKit.

Note: For Development platform identification purpose, Product part number is pasted as Label with Barcode

readable format.

Summary of Contents for Zynq-7000 SoC



























































Search results

Summary of Contents for Zynq-7000 SoC

Reviews:

Related manuals for Zynq-7000 SoC

Brands by name

Popular brands

iWave Zynq-7000 SoC, Hardware User'S Manual

Search results

Summary of Contents for Zynq-7000 SoC

Reviews:

Related manuals for Zynq-7000 SoC

Brands by name

Popular brands