iWave iW-RainboW-G7D Hardware User'S Manual Download Page 81 | Manualshive

Page: 81 / 164

background image

Rev 2.0

Page 81 of 164

Generic Qseven Carrier Board Hardware User Guide

iWave Systems Technologies Pvt. Ltd.

2.8

Additional Features

2.8.1

JTAG Connector

Qseven Generic Carrier Board supports 10-pin JTAG connector for debug purpose. Since both UART and
JTAG share the same pins of Qseven MXM connector, a jumper option (J37) is provided to select either
one. This Jumper is connected to 204

th

Pin of Qseven MXM connector. If the Jumper is open UART is

selected as Debug port and if closed JTAG is selected as Debug port. For further information on these
signals refer section “Manufacturing Signals” of Qseven-Spec_2.0. JTAG connector (J32) is physically
located at the bottom of the board as shown below.

Number of Pins: 10
Connector Part number: GRPB052VWVN-RC
Mating Connector: LPPB052CFFN-RC from Sullins Connector Solutions

Figure 23: JTAG Connector

Note: To support this dynamic selection, Qseven module which is connected to this Generic carrier board
also should support dynamic selection. By default jumper is open and UART is selected as Debug port.

«
...
79
80
81
82
83
...
»

Summary of Contents for iW-RainboW-G7D





































































































































































Reviews:

No comments

Related manuals for iW-RainboW-G7D

Brand: Emmaljunga Pages: 84

Brand: JANE Pages: 83

Brand: CYBEX Pages: 62

Brand: KIDDY Pages: 101

Brand: JANE Pages: 53

Brand: ICM Controls Pages: 2

Brand: Infantino Pages: 6

Flip Front2Back

Brand: Infantino Pages: 8

TRANSAT CONFORT

Brand: Aubert concept Pages: 5

Porte enfant souple

Brand: Aubert concept Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands