iWave iW-RainboW-G7D Hardware User'S Manual Download Page 40

Page: 40 / 164

Rev 2.0

Page 40 of 164

Generic Qseven Carrier Board Hardware User Guide

iWave Systems Technologies Pvt. Ltd.

2.5.3

USB Ports

2.5.3.1

USB Host0 & Host2 Ports

USB Host0 & Host2 interfaces from Qseven MXM connector are connected to dual stack USB Type-A
connector (J25B). Refer.

Figure 5

for the connector location.

Table 8: USB 2.0 Host Ports Connector Pin Outs

Pin No

Pin Name

Signal Type

Voltage Level/

Termination

Description

VBUS1

Power

USB Host Port 0, 5V Power (Bottom).

D1-

Input/Output Differential

USB Host Port 0, Data negative (Bottom).
Connected to 94

Pin of Qseven MXM

Connector.

D1+

Input/Output Differential

USB Host Port 0, Data Positive (Bottom).
Connected to 96

Pin of Qseven MXM

Connector.

GND1

Power

USB Host Port 0 Ground (Bottom).

VBUS2

Power

USB Host Port 2, 5V Power (Top).

D2-

Input/Output Differential

USB Host Port 2 Data negative (Top).
Connected to 88

Pin of Qseven MXM

Connector.

D2+

Input/Output Differential

USB Host Port 2 Data Positive (Top).
Connected to 90

Pin of Qseven MXM

Connector.

GND2

Power

USB Host Port 2 Ground (Top).

S1,S2

SHLD

Power

Shield Ground (Bottom).

S3,S4

SHLD

Power

Shield Ground USB2 (Top).

Summary of Contents for iW-RainboW-G7D





































































































































































Search results

Summary of Contents for iW-RainboW-G7D

Reviews:

Related manuals for iW-RainboW-G7D

Brands by name

Popular brands

iWave iW-RainboW-G7D, Hardware User'S Manual

Search results

Summary of Contents for iW-RainboW-G7D

Reviews:

Related manuals for iW-RainboW-G7D

Brands by name

Popular brands