iWave iW-RainboW-G35D Hardware User'S Manual Download Page 39

Page: 39 / 110

REL0.2

Page 39 of 110

iWave Systems Technologies Pvt. Ltd.

Zynq Ult MPSoC (ZU11/17/19EG) SOM DevKit Hardware User Guide

2.5.1.2

SDI Video IN

The Zynq Ult MPSoC (ZU11/17/19EG) Carrier board supports one 3G/12G SDI Video IN interface through HD

BNC connector (J29). The Video input signals from HD BNC Connector is directly connected to Adaptive Cable Equalizer

chip and then connected to PL Bank227 Channel3 GTH receiver of Zynq Ult MPSoC through Board to Board

connector2.

The Zynq Ult MPSoC (ZU11/17/19EG) Carrier board supports Video Input Lock status LED (D17) for presence

and absence of the Video Input signal on HD BNC connector (J29). This LED will glow when the Video Input signal is

detected on HD BNC connector (J29). Also PS I2C0 is connected to Adaptive Cable Equalizer chip for control and

configuration with I2C address 0x2D. SDI Video IN HD BNC connector (J29) is physically located at the top of the board

as shown below.

Note: By default, 12G Adaptive

Cable Equalizer chip “LMH1297” is

supported on the board. To support 3G Adaptive

Cable Equalizer chip

“LMH

97”

, contact iWave.

Figure 19: SDI Video IN HD BNC Connector

Summary of Contents for iW-RainboW-G35D















































































































Search results

Summary of Contents for iW-RainboW-G35D

Reviews:

Related manuals for iW-RainboW-G35D

Brands by name

Popular brands

iWave iW-RainboW-G35D, Hardware User'S Manual

Search results

Summary of Contents for iW-RainboW-G35D

Reviews:

Related manuals for iW-RainboW-G35D

Brands by name

Popular brands