iWave iW-G36S-2CG1-4E002G-E008G-BEA Hardware User'S Manual Download Page 73

Page: 73 / 88

REL0.2

Page 73 of 88

Zynq Ult MPSoC SBC Hardware User Guide

iWave Systems Technologies Pvt. Ltd.

2.11.1.2

PL IOs

–

HD BANK44

The Zynq Ult MPSoC SBC supports 12 LVDS IOs/24 Single Ended (SE) IOs on Board to Board Connector3 from

MPSoC

’s

PL High-Density (HD) Bank44. Upon these 12 LVDS IOs/24 SE IOs, upto 4 HDGC Global Clock Inputs and upto

8 PLSYSMON auxiliary analog inputs are available.

The IO voltage of Bank44 is connected from LDO3 output of the PMIC and supports variable IO voltage setting. IO

voltage is configurable from 1.2V to 3.3V through software. While using as LVDS IOs or Single Ended IOs, make sure to

set the PMIC LDO3 to output appropriate IO voltage for PL Bank44. By default, IO voltage of PL Bank44 is set as 1.2V

and after U-boot bootup configured to 1.8V. For more details about supported IO standard, refer the Zynq Ult

MPSoC datasheet.

In the Zynq Ult MPSoC SBC, PL Bank44 signals are routed as LVDS IOs to Board to Board Connector3. Even

though PL Bank44 signals are routed as LVDS IOs, these pins can be used as SE IOs if required. The Board to Board

Connector3 pins 5, 6, 7, 8, 11, 12, 17, and 18 are HDGC Global Clock Input capable pins of PL Bank44. Also Board to

Board Connector3 pins 1, 2, 3, 4, 13, 14, 15, 16, 21, 22, 23, 24, 25, 26, 29 and 30 are PLSYSMON auxiliary analog Input

capable pins of PL Bank44.

Note: In ZCU2 & ZCU3 MPSoC devices, the PL Bank 43, 44, 45 & 46 is called as 44, 24, 25 & 26 respectively. Only the

Bank Numbering is different and all other functionalities remain same.

For more details on PL HD Bank44 pinouts on Board to Board Connector3, refer the below table.

B2B3

Pin No

Signal Name

MPSoC

Pin Name

MPSoC

Bank

MPSoC

Pin No

Signal Type/
Termination

Description

PL_AE13_LVDS44
_L4P

IO_L4P_AD12P_44

AE13

IO, 1.8V LVDS PL Bank44 IO4 differential

positive.
Same

can

configured as PLSYSMON
differential analog input12
positive or Single ended
I/O.

PL_AF13_LVDS44
_L4N

IO_L4N_AD12N_44

AF13

IO, 1.8V LVDS PL Bank44 IO4 differential

negative.
Same

can

configured as PLSYSMON
differential analog input12
negative or Single ended
I/O.

Summary of Contents for iW-G36S-2CG1-4E002G-E008G-BEA

























































































Search results

Summary of Contents for iW-G36S-2CG1-4E002G-E008G-BEA

Reviews:

iWave iW-G36S-2CG1-4E002G-E008G-BEA, Hardware User'S Manual, Page: 73 / 88

Search results

Summary of Contents for iW-G36S-2CG1-4E002G-E008G-BEA

Reviews: