background image

20

Integrated Technical Vision Ltd

http://www.itvsystems.com.ua

071004

Limited Warranty

Integrated Technical Vision Ltd. warrants that for a period of eighteen months from
the date of purchase, the product shall be free of defect in materials and workman-
ship under normal use and that in fulfilment of any breach of such warranty,
Integrated Technical Vision  Ltd. shall, at its option, repair or replace the defective
equipment upon return of the equipment to its repair depot. This warranty applies
only to defects in parts and workmanship and not damaged incurred in shipping or
handing, or damaged due to causes beyond the control of Integrated Technical
Vision Ltd. such as lightning, excessive voltage, mechanical shock, water damage,
or damage arising out of abuse, alteration or improper application of the equipment.
The foregoing warranty shall apply only to the original buyer, and is and shall be lieu
of any and all other warranties, whether expressed or implied and of all other
obligations or liabilities on the part of Integrated Technical Vision Ltd. This
warranty contains the entire warranty. Integrated Technical Vision Ltd. neither
assumes, nor authorizes any other person purporting to act on its behalf to
modify or to change this warranty, nor to assume for it any warranty or liability
concerning this product.
In no event shall Integrated Technical Vision Ltd. be liable for any direct, indirect
or consequential damages. Loss of anticipated profits, loss of time or any other
losses incurred by the buyer in connection with the purchase, installation or
operation or failure of this product.

Limited Warranty

Summary of Contents for DLK642





















Reviews: