background image

ITT assumes no liability for these situations:

• Bodily injuries
• Material damages
• Economic losses

Warranty claim

ITT products are high-quality products with expected reliable operation and long life. However, should the
need arise for a warranty claim, then contact your ITT representative.

Safety

WARNING:

• The operator must be aware of  safety precautions to prevent physical injury.
• Any pressure-containing device can explode, rupture, or discharge its contents if  it is over-pressurized.

Take all necessary measures to avoid over-pressurization.

• Operating, installing, or maintaining the unit in any way that is not covered in this manual could cause

death, serious personal injury, or damage to the equipment. This includes any modification to the
equipment or use of  parts not provided by ITT. If  there is a question regarding the intended use of
the equipment, please contact an ITT representative before proceeding.

• Installation, Operation, and Maintenance manuals clearly identify accepted methods for disassembling

units. These methods must be adhered to. Trapped liquid can rapidly expand and result in a violent
explosion and injury. Never apply heat to impellers, propellers, or their retaining devices to aid in their
removal.

• Do not change the service application without the approval of  an authorized ITT representative.
• Never operate the pump below the minimum rated flow, when dry, or without prime.
• Never operate the pump without safety devices installed.
• Never operate the pump with the discharge valve closed.
• Never operate the pump with the suction valve closed.

Observe all safety messages highlighted in other sections of  this manual.

Safety terminology and symbols

About safety messages

It is extremely important that you read, understand, and follow the safety messages and regulations
carefully before handling the product. They are published to help prevent these hazards:

• Personal accidents and health problems
• Damage to the product
• Product malfunction

Hazard levels

Hazard level

Indication

DANGER:  

A hazardous situation which, if  not avoided, will

result in death or serious injury

WARNING:  

A hazardous situation which, if  not avoided, could

result in death or serious injury

Introduction and Safety

i-ALERT

 Condition Monitor Installation, Operation, and Maintenance Manual

3

Summary of Contents for Goulds Pumps i-ALERT

























Reviews: