background image

1.  Turn the Faucet handles to OFF position.
2.  Press and hold the Reset Button for 3 seconds until 

the green light flashes and then release the button.

3.  Wait Until the green flashing light stops. Sensor 

range/EZ Faucet is set and ready for use after turning 

the faucet handles to ON position (adjust and check 

the water temperature properly before use – see 

Setting Water Temperature and Flow Rate section.

Note:

 If the sensor is too sensitive, try putting your hand 

3”~ 5” below the sensor while programming the sensor 

range. This will shorten the sensor range. 

Program 

the Sensor 

Range / 

Reset the 

EZ Faucet 

(FIG. E)

1.  Turn faucet handles to COLD position.
2.  Press Manual Override Button once 

(FIG. E)

.

3.  While the water is running, move existing faucet 

handles to adjust water temperature and flow rate.

4.  After water temperature and flow rate is set, press 

Manual Override to turn off the water. Automatic 

feature is resumed.

Setting 

Water 

Temperature 

and Flow 

Rate

It is optimal to use 4 Alkaline batteries with the same 

brand. They will last longer and keep your EZ Faucet at 

best performance. Approximately 1 to 2 weeks before 

the batteries drain completely, the orange POWER LOW 

indicator will begin to flash. Change all batteries as 

soon as possible. (see Changing Battery section).

Low Battery 

Indicator

itouchless

.com  |  844.660.7978

User Manual

EZ FAUCET

TOUCH FREE ADAPTOR®

(EZF003C)

1.  Remove existing faucet aerator by turning 

counter-clockwise. Use the “Hexnut” Wrench, pliers, or 

vice grips if it is tight 

(Fig. A)

.

2.  After aerator is removed, ensure that the rubber 

washer from existing aerator is removed. If the washer 

is not in the lip of the existing aerator, it should be 

inside the water exit of the existing faucet.

3.  Before installing the EZ Faucet, check if your faucet exit 

has Inside Thread (female adaptor) or Outside Thread 

(male adaptor) type. Female adaptor type: Insert the 

Rubber Washer that comes with package into the 

Adaptor 

(FIG. C1)

. Male adaptor type: Do not use any 

rubber washer 

(FIG. C2)

.

4.  Install EZ Faucet by turning the EZ Faucet Adaptor 

clockwise to attach to the faucet (first use fingers to 

tighten, then use included “Hexnut” Wrench 

(FIG. D)

 for 

a final snug fit).

5.  Remove EZ Faucet battery cover (see No.2 in Changing 

Battery section) and insert 4 new AAA Batteries (make 

sure batteries are inserted in the correct directions (+ 

and -) as indicated in the battery holder). Close the 

battery door firmly 

(FIG. B)

.

6.  Press and hold the Reset Button down for 3 seconds to 

adjust the sensor rangeautomatically. EZ Faucet is 

ready for use after turning the faucet handles to ON 

position (adjust and check the water temperature 

properly before use – see Setting Water Temperature 

and Flow Rate section) 

(FIG. E)

.

Quick 

Installation 

Guide

1.  Turn the faucet handle to OFF position.
2.  Remove the battery holder by pulling the battery 

holder out of the compartment.

3.  Take the 4 batteries out one-by-one and replace with 

new batteries (make sure to put batteries in correct 

directions).

4.   Close battery holder by pushing the battery holder 

into the compartment until it is firm. Then adjust the 

sensor range (see Program the Sensor Range section).

Changing the 

Batteries

© 2019 All Rights Reserved. iTouchless Housewares & Products, Inc. 

San Mateo, CA 94404 USA

We’re here to help!

If you have any questions or concerns about this product, 

please contact Customer Support for immediate 

assistance. You can reach us at 1-844-660-7978.  

Your 100% satisfaction is our #1 goal!

Register your Product

Go to itouchless.com to register your product for simple 

warranty service and to receive product updates and 

special offers.   
Product Model # EZF003C

Contents of the Box:

•  One (1) EZ faucet™ adapter
•  One (1) Hexnut wrench
•  One (1) Rubber washer
•  User Manual

Reviews: