Itel DPRO3 User Manual Download Page 48 | Manualshive

Page: 48 / 59

background image

48

DPRO3 FM Audio Processor

© 2016 ITEL Elettronica e Telecominicazioni Snc

4.3

Configuration

Open configuration menu (

Tools->Configuration

), and the following window will appear:

4.3.1

Setup

4.3.1.1

Program ID

It is possible to assign a name to the executable window in order to recognize it quickly, when
multiple executables are running at the same time to control different coders (eg different programs
belonging to the same publishing group).

4.3.1.2

Radiotext Plus and dynamic PSN

Enable RT +:

Enable radiotext plus

The strings sent by radio automation system will be passed to radiotext only if this flag is enabled.
You can also add a prefix and a separator to the string which will be put on-air.
Please note that the maximum length of radiotext string in block 2A, is 64 characters.
If the total length of the string, including prefix and separator, will be longer than this limit, it will be
truncated automatically.

Send RT + titles to PSN:

Enable sending radiotext titles on PSN.

With this function, the song titles will also be sent on the PSN (maximum length is 8 characters ).
This function should be used with caution as it can cause driver distraction and in some countries is
expressly prohibited. You are advised to check your local regulations before to activate it.

«
...
46
47
48
49
50
...
»

Summary of Contents for DPRO3




























































Reviews:

No comments

Related manuals for DPRO3

Brand: EAW Pages: 6

Brand: EAW Pages: 6

Brand: F5 Pages: 2

Brand: F5 Pages: 90

Brand: F5 Pages: 47

Brand: Hama Pages: 4

Brand: IEI Technology Pages: 21

Brand: Xinje Pages: 57

Brand: Keithley Pages: 59

Brand: Paradyne Pages: 1

Brand: Quectel Pages: 23

Brand: Bridgeworks Pages: 18

DHI-NVR2104-P-4KS2

Brand: Dahua Pages: 23

Active Module Carrier VX402C-64

Brand: C&H Pages: 32

Brand: H3C Pages: 3

Brand: Cisco MERAKI Pages: 4

Brand: Aewin Technologies Pages: 86

Brand: Kontron Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands