Itel DPRO3 User Manual Download Page 18 | Manualshive

Page: 18 / 59

background image

18

DPRO3 FM Audio Processor

© 2016 ITEL Elettronica e Telecominicazioni Snc

2.3

Audio input setup

In this section are present all controls related to audio sources and

automatic audio fallback

2.3.1

Audio levels monitor and input level setting

In the current window is displayed, with greater accuracy, the input level of the selected channel.

The input level of the selected channel can be adjusted, but the channel will not be put on air.
To change the on air input channel, the following window must be used.

2.3.2

Audio source setup

Audio input:

Analog, analog input
Digital, AES/EBU input
SDI or NetAudio, streaming audio input

The initial adjustment of the input level should be made so that the maximum analog input level is
equal to or only slightly above that limit.

In no case the front panel "CLIP" led should light.

Dig. lev:

AES/EBU level adjustment

Net lev:

streaming module level adjustment.

«
...
16
17
18
19
20
...
»

Summary of Contents for DPRO3




























































Reviews:

No comments

Related manuals for DPRO3

eXtremeRAID 1100

Brand: Mylex Pages: 74

Brand: Orban Pages: 255

Brand: Altera Pages: 42

AyrMesh IndoorAP

Brand: AYRSTONE Pages: 2

iTRON B 70.2040

Brand: JUMO Pages: 41

Brand: Lutron Electronics Pages: 4

Brand: Teletronics International Pages: 57

Brand: H3C Pages: 68

Brand: Kontron Pages: 32

Service Aggregation Router 7705

Brand: Alcatel-Lucent Pages: 20

Xtreme Networked Boat

Brand: Broadband Products Pages: 16

Brand: SilverStone Pages: 17

Brand: TECO Pages: 24

Brand: Atmel Pages: 123

Brand: Agilent Technologies Pages: 458

Brand: VALKYRIE Pages: 26

StorageGRID Webscale SG5700 Series

Brand: NetApp Pages: 15

C32C824151 - UB E02 Print Server

Brand: Epson Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands