manualshive.com logo in svg

Itel DPR06 FM, User Manual

Share
Download
Itel DPR06 FM User Manual Download Page 20

20

DPRO6 FM Audio Processor

© 2016 ITEL Elettronica e Telecominicazioni Snc

2.5.2

Output level setup

Audio level: 

percentage of audio signal (L+R, L-R) into the composite MPX signal.

In case of monoaural broadcasting, without RDS  and pilot  subcarrier,  this  level can be left  at  100%,
and this will produce a deviation of 75KHz.
In  all  other  cases  it  should  be  reduced  according  to  the  level  of  injection  of  the  two  subcarriers,
otherwise overmodulation will occur.
For example, if a RDS subcarrier of 2KHz and a pilot tone of 6KHz are desired, the audio signal level
can not be greater than

100*(1- ((PilotCarrierDeRDSCarrierDeviation)/75))
which, for the example described above, will correspond to:
100*(1- ((6+2)/75))=89.3% 

Composite level:

 MPX output level. 

Test  tone  (!):

 when  activated,  will  put  on  air  a  400Hz  tone,  having  an  amplitude  equal  to  100%

modulation.
If RDS and pilot subcarriers were correctly set, the final modulation will not go above this limit.

Summary of Contents for DPR06 FM



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands