Itel DPR06 FM User Manual Download | Manualshive

Page: 19 / 58

background image

19

Front panel display

© 2016 ITEL Elettronica e Telecominicazioni Snc

2.4

Audio output setup

2.4.1

Audio output regulation

ANA LR Out :

audio output level on rear XLR Left-Right OUT connector.

DIG LR Out :

output audio level on rear XLR DIG OUT connector

Out deemph:

output audio deemphasis. This is related only to the audio output, not to MPX output.

Out pos:

point of acquisition of the output signal, it can be selected form:

Post clip&flt:

output signal is taken after clipper and lowpass filter.

Pre filter:

output signal is taken prior the lowpass filter, but after the clipper.

Pre clipper:

output signal is taken before the clipper.

2.5

MPX output setup

2.5.1

MPX modulation and pilot subcarrier setup

Modulation (stereo, mono l+r, mono L, mono R):

Stereo: stereo modulation
Mono L+R: monoaural modulation from L+R channels sum.
Mono L, Mono R:monoaural modulation from a single channel.

Preemphasis:

50/75uS preemphasis, it should be set according to local FM broadcasting

standards.

Pilot level:

19KHz pilot tone injection level.

Pilot Phase:

pilot tone phase adjustment.

«
...
17
18
19
20
21
...
»

Summary of Contents for DPR06 FM



























































Reviews:

No comments

Related manuals for DPR06 FM

ShareCenter DNS-320L

Brand: D-Link Pages: 4

Brand: Cabletron Systems Pages: 21

Brand: Patton electronics Pages: 51

Brand: Teagle Pages: 40

Brand: ebm-papst Pages: 6

Brand: ebm-papst Pages: 6

Brand: ebm-papst Pages: 5

PG-FlexPlus AMU-912

Brand: ADC Pages: 130

Brand: Fieldbus Specialists Pages: 39

Brand: hilscher Pages: 154

Brand: Moxa Technologies Pages: 2

ZyXEL ZyAIR B-120

Brand: ZyXEL Communications Pages: 20

Brand: Omron Pages: 13

Brand: ZKTeco Pages: 68

CNPS7000A Series

Brand: ZALMAN Pages: 9

Tamar FCSAS102800

Brand: Bridgeworks Pages: 56

Brand: Uctronics Pages: 2

Brand: Alphacool Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands