Itel DPR06 FM User Manual Download | Manualshive

Page: 17 / 58

background image

17

Front panel display

© 2016 ITEL Elettronica e Telecominicazioni Snc

2.3

Audio input setup

2.3.1

Audio levels monitor and input level setting

In the current window is displayed, with greater accuracy, the input level of the selected channel.

The input level of the selected channel can be adjusted, but the channel will not be put on air.
To change the on air input channel, the following window must be used.

2.3.2

Audio source setup

Audio input:

Analog, analog input
Digital, AES/EBU input
SDI or NetAudio, streaming audio input

The initial adjustment of the input level should be made so that the maximum analog input level is
equal to or only slightly above that limit.

In no case the front panel "CLIP" led should light.

Dig. lev:

AES/EBU level adjustment

Net lev:

streaming module level adjustment.

2.3.3

Audio processor preset selection

«
...
15
16
17
18
19
...
»

Summary of Contents for DPR06 FM



























































Reviews:

No comments

Related manuals for DPR06 FM

Brand: Paradyne Pages: 20

Compshere 3000 Series

Brand: Paradyne Pages: 2

Brand: Vivotek Pages: 136

Brand: Compaq Pages: 112

Brand: Omega Engineering Pages: 34

SuperServer 5019S-L

Brand: Supermicro Pages: 61

Brand: Time domain Pages: 64

Brand: Roland Pages: 2

Brand: Realtek Pages: 30

Brand: FONESTAR Pages: 8

Brand: Valcom Pages: 4

Brand: Omron Pages: 13

Brand: Commell Pages: 36

Brand: Acromag Pages: 35

X-NUCLEO-EEPRMA1

Brand: ST Pages: 22

Brand: Inspired Energy Pages: 5

Brand: Jabra Pages: 2

Brand: Vivotek Pages: 185

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands