manualshive.com logo in svg

Itel DPR06 FM, User Manual

Share
Download
Itel DPR06 FM User Manual Download Page 10

10

DPRO6 FM Audio Processor

© 2016 ITEL Elettronica e Telecominicazioni Snc

2

Front panel display

Following are listed all menus and functionalities available on the current firmware release.

2.1

Audio processor

2.1.1

AGC

This window contains the settings for the dual band automatic gain control (AGC) block, placed at
the head of audio processing chain.
The automatic gain control performs a pre-leveling of the signal applied to the following compressors/
limiters, keeping their working point almost constant.
At the right side of the bar which indicates the level of pre-amplification applied to the input signal, is
placed the AGC status indicator: if "gate" indication is off, the input level is above the gate threshold
and the AGC and compressors/limiters are operating correctly, if "gate" indication is on, it means
that the input signal is below the minimum level so the AGC release is slowed down and the AGC
will slowly raise its gain.

Release (...): 

AGC release time setting (40% fastest, 200% slowest).

Gate:

 Gate level serring. Below this level, the AGC and multiband limiter release is slowed down. 

Link:

 set the maximum compression difference between the bass and middle/highs band.

Setting this value to zero, the bass compression level will be totally independent and this will cause
also a mild auto-equalization.
Setting this value to 100%, it will force the bass compressor to have a gain never greater than the
middle/highs band giving a sound very close to the original.

Drive:

 indicates the AGC input driving level, thus determining the AGC maximum gain .

2.1.2

Compression levels

In the window, the gate status and compression-limiting levels of the multiband limiters are shown.

Summary of Contents for DPR06 FM



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands