background image

 

 

6.2 Protections 

 

Protection 

 

 

Battery Over Voltage 

Battery has reached or 

exceeded the over-

voltage point 

Controller will 

automatically stop 

charging and 

discharging 

Battery Over 

Discharge 

Battery voltage has 

dropped below the 

Low voltage disconnect 

point 

Controller will turn off 

the load and only 

recover once the 

battery has charged 

above the low voltage 

reconnect voltage. 

Overload 

The connected load 

exceeds the rated 

current 

The load will 

automatically be 

turned off 

6.3 Charging Profiles 

NOTE: Values with (E) next to them indicates user adjustable values. For 

iTechworld Lithium Batteries, please use LiFePO4(4-3.2) only, please refer to 

section 4.4.1.

 

 

 

 

- 20 - 

 

Re-Bulk 

Bulk 

Eq 

Abs 

Flt 

LVD 

LVR 

Usr1 

13.0 

14.4 

14.6

(E) 

14.4

(E) 

13.8

(E)

  10.8

(E)

  12.6

(E)

 

Gel 

13.6 

14.4 

14.2 

14.2 

13.8 

10.8 

12.6 

Sld 

13.6 

14.4 

14.6 

14.4 

13.8 

10.8 

12.6 

Fld 

13.6 

14.4 

14.8 

14.6 

13.8 

10.8 

12.6 

LiFePO4

 

(4-3.2) 

13.0 

14.40 

14.2 

14.4 

13.8 

11.2 

12.8 

LiFePO4

 

(5-3.2) 

16.2 

18.0 

14.2 

14.4 

13.8 

14.0 

16.0 

LiPo 

(3-3.7) 

12.0 

12.6 

14.4 

14.4 

13.8 

9.9 

11.1 

LiPo 

(4-3.7) 

16.0 

16.8 

14.4 

14.4 

13.8 

13.2 

14.8 

Usr2 

13.6(E)

  14.4

(E)

 

14.2 

14.2 

13.8 

10.8 

12.6 

Summary of Contents for 40Amp MPPT

























Reviews: