PRELIMINARY
2 channel receiver model
RXJR-2C
compatible with transmitter model
JANE-R
(red LED)
2 channel receiver model
RXJF-2C
compatible with transmitter model
JANE-F
(blue LED)
FEATURES
• 2 channel receiver with 2 relays equipped with OOK / ASK super heterodyne receiver
• microcontroller with decoding functions
• self-learning remote controls
• digital noise reduction filter
• independent mode switching for each channel
• SAW filter to suppress noise outside the band
• power supply with noise reduction filters and surge protection on power lines
APPLICATIONS
Remote control for automation, light switches, blinds, curtains etc.
All programming and configuration of channels carried out using the single
button on the circuit board. The colour of the LED matches the channel:
Green LED:
all operations related to channel 1
Red LED:
all operations related to channel 2
Orange LED:
if both channels are turned on
STORING A JANE on the RX RECEIVER
CHANNEL 1
• Press the button once and release: the green
LED
lights up
• within 5 seconds make a transmission by pressing the JANE button to be associated with channel 1
• the green
LED
goes off for 0.5 seconds to confirm learning
• after 5 seconds the green
LED
goes off indicating the end of the learning phase
CHANNEL 2
• Press the button twice and release: the red
LED
lights up
• within 5 seconds make a transmission by pressing the JANE button to be associated with channel 1
• the red
LED
goes off for 0.5 seconds to confirm learning
• after 5 seconds the red
LED
goes off indicating the end of the learning phase
Each receiver consists of:
1. Double-sided adhesive support
2. Back plate
3. Two stainless steel screws
4. Electronic circuit board
5. Front shell
Signals on the Terminals:
1. power supply input (positive supply)
2. earth (negative supply)
3. common relay output 1
4. contact n.o. output 1
5. common relay output 2
6. contact n.o. output 2
7. aerial shielding
8. aerial input
1
2
4
5
3
Two-colour LED
Button
22 mm
51 mm
16.2 mm
Patented pr
oduct
®
via Spessa,
12/14 - 36051 Cr
eazzo -
Vicenza
www
.telecomandojane
.it
Guarantee: 24 months
Manufacturing and technology: 100% made in Italy
Patented product
Declaration of conformity:
The undersigned,
Luigino Pellattiero
, legal representative of
ITALFILE srl
, declares
that the receiver cod.
RXJF-2C
/
RXJR-2C
manufactured in 2010, was assembled in
compliance with the following standards:
Directive 2004/108/CE
: known as Electromagnetic Compatibility directive
Directive 2002/95/CE
: Known as directive RoHS
And therefore complies with current standards.
Luigino Pellattiero - Vicenza (Italy) 1-10-2011
Max. Permissible Values
Supply Voltage
33VAC / 35VDC
RF Input
+ 20 dBm
GND voltage of output pins
120V
Storage temperature
- 40 / + 100 °C
Operating temperature
- 20 / + 70 °C
Electrical characteristics at 25 °C:
Parameter
Min Typical
Max
Unit
Notes
Supply Voltage (VDC)
12
-
30
volts
-
Supply Voltage (VAC)
12
-
28
volts
-
Absorbed current (receive only)
-
11
-
mA
-
Absorbed current (1 active channel)
-
25
-
mA
-
Absorbed current (2 active channels)
-
36
-
mA
-
Centre frequency
-
433.92
-
MHz
-
Sensitivity
-
-105
-
dBm
Note 1
Passband RF – 3dB
-
+- 100
-
kHz
-
Spurious aerial signals
-
-
-60
dBm
-
Switch on time
-
-
2.8
S
Note 2
Command implementation time
-
-
0.5
S
Note 3
Max. contact output VDC
-
-
1A 24V
Amp vdc
-
Max. contact output VAC
-
-
1A 120V
Amp vac
-
Note 1
: measurement carried out with 100% AM modulated signal, square wave, at frequency 1 kHz
Note 2
: time period between switching on and reception of a valid sequence of data
Note 3
: time period between command transmission (remote control button press) and its implementation (relay trip)
Note 4
: all measurements relating to the RF parameters are valid with the 3 pin connected to a source or load impedance of 50 ohms