manualshive.com logo in svg

Isotech Pegasus R 970, User Maintenance Manual/Handbook, Page: 14 / 24

Share
Download
Isotech Pegasus R 970 User Maintenance Manual/Handbook Download Page 14

 

Page 14 of 24 

Pegasus R Iss.07 – 08/13 

METHOD 

Evaluation of the Optical Bench 

 

The Pegasus 'R' item was set up in the 'normal' position as described above.  The controller temperature was set to 
1000 C.  After stabilisation the 3 freedom of movement were evaluated. 

 

a. 

Back & Forth

 

 

The optical pyrometer was moved back & forth by 100mm.  The following readings were obtained. 

       

 

 

 

 

OPTICAL PYROMETER READING

 

 

650mm from rear of target to optical pyrometer 

750mm 

850mm 

 

984 

983 

983 

 

   

b. 

At a distance of 750mm.  The focal length of the optical pyrometer was changed. 

 

 

 

 

METRES FOCAL LENGTH

 

 

 

READING

 

.75 

.8 

.85 

.9 

983 
983 
983 
983 

 

c. 

The height of the optical pyrometer was altered 

    

 

 

 

 

READING  C

 

 

-2mm 

 

Normal 

 

+2mm 

 

982 

 

983 

 

982 

               

d. 

The lateral position of the optical pyrometer was adjusted and the optical pyrometer rotated to align with the 

centre of the target. 

 

 

 

LATERAL MOVEMENT

 

 

 

READING  C

 

 

Right (mm) 

5 

10 

Left (mm) 

5 

10 

 

 

983 

983 

 

983 

983 

 

 

Summary of Contents for Pegasus R 970

























Reviews:

No comments