manualshive.com logo in svg

Isilon Systems Isilon IQ 32000X-SSD, Field Replacement Manual, Page: 27 / 40

Share
Download
Isilon Systems Isilon IQ 32000X-SSD Field Replacement Manual Download Page 27

1

1  I/O panel captive screw

Figure 16. 4U Isilon IQ rear panel

3. Replace the node top panel.

For more information, see 

Install the node top panel

 on page 39.

4. Connect both power cables to the node power supplies and verify that the node starts properly and displays the login

prompt.

Note:  If a node fails to start properly or the node displays errors relating to the journal, contact Isilon Technical
Support.

Replacing the IB/NVRAM card

Isilon IQ nodes include a combination InfiniBand/non-volatile RAM (IB/NVRAM) card.

Prerequisite:  Before replacing the InfiniBand/non-volatile RAM (IB/NVRAM) card, you must remove the PCIe riser
card assembly. For more information, see 

Removing the riser card assembly

 on page 25.

1. Remove the failed IB/NVRAM card.

2. Install the new IB/NVRAM card.

3. Return the old hardware to Isilon Technical Support.

For more information, see 

General recommendations

 on page 6.

Remove the IB/NVRAM Card

Remove the InfiniBand/non-volatile RAM (IB/NVRAM) card from a node to transfer it to a replacement node, or to
clear space for a card tranferring in from a failed node.

Prerequisite:  Before replacing the IB/NVRAM card, you must remove the riser card assembly. For more information,
see 

Removing the riser card assembly

 on page 25.

1. Disconnect the IB/NVRAM 8-position cable from the back of the IB/NVRAM card.

©

 2011 Isilon Systems, LLC.

27

Expansion cards

Summary of Contents for Isilon IQ 32000X-SSD









































Reviews:

No comments