Isilon Systems Isilon IQ 32000X-SSD Page 26 Field Replacement Manual Download | Manualshive

Page: 26 / 40

background image

Important: Do not disconnect drive cables from the SAS drive controller card unless you are replacing the
SAS drive controller card. Also, Do not disconnect the 8-position cable assembly from the
InfiniBand/non-volatile RAM (IB/NVRAM) card unless you are replacing the IB/NVRAM card.

1

1 PCIe riser card assembly

Figure 14. PCIe riser card assembly

Installing the riser card assembly

Installing the riser card assembly connects the SAS drive controller card and the IB/NVRAM card to the node motherboard.

1. Insert the riser card assembly into the PCI Express slot on the node motherboard ensuring that the riser card is fully

seated in the motherboard connector.

1

1 Riser card assembly

Figure 15. PCIe riser card assembly

2. Tighten the captive screw on the rear I/O panel.

26

©

2011 Isilon Systems, LLC.

Expansion cards

«
...
24
25
26
27
28
...
»

Summary of Contents for Isilon IQ 32000X-SSD









































Reviews:

No comments

Related manuals for Isilon IQ 32000X-SSD

Expansion Chassis

Brand: Dayna Pages: 7

Brand: Gooxi Pages: 20

Brand: Supermicro Pages: 32

Brand: InWin Pages: 10

Brand: Cabletron Systems Pages: 2

Echo Express SE III

Brand: Sonnet Pages: 14

Echo Express III-D Thunderbolt 3 Edition

Brand: Sonnet Pages: 14

echo express SE II

Brand: Sonnet Pages: 16

Echo Express SE I

Brand: Sonnet Pages: 16

Brand: Supermicro Pages: 85

Project M Chassis

Brand: saberz Pages: 29

Flex System Enterprise Chassis Airborne Contaminant Filter

Brand: IBM Pages: 12

Brand: Reely Pages: 108

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands