manualshive.com logo in svg

ISGM i-2UVA, User Manual, Page: 16 / 40

Share
Download
ISGM i-2UVA User Manual Download Page 16

16

Product Version 1.0 | Revision A | Released 2022-2-21

Figure 10: Connecting data to USB up-loader 

cable for POI fixtures

STEP 5: Step 5 Disconnect up-loader cable from computer, then 
disconnect up-loader cable from fixture.
Repeat Steps 2-5 for more fixtures. Multiple fixtures can be ad

-

dressed  and  configured.  Contact  your  SGM  representative  for 
more information on multiple fixture addressing.

PLEASE NOTE! AT A MINIMUM, ALL FIXTURES WILL NEED TO 
BE GIVEN A DMX ADDRESS AND DMX PERSONALITY IN OR

-

DER TO PATCH AND PROGRAM ON A CONTROLLER. 

All configuration of POI fixtures is done through the SGM Addressing Tool. The SGM Addressing Tool is a windows 
based program designed to allow the user to configure the fixture through the RDM protocol. All settings on a stan

-

dard fixture are available on a POI fixture. But on POI, these settings are changed through the Addressing Tool.

• 

STEP 1: Click Full Discovery and look for the green light to light up on the fixture. If the green light does not 
appear, cycle power or refer to troubleshooting.

• 

STEP 2: Select the standard settings tab and enter a DMX address and a personality/mode of operation. Look 
for the LED indicator to blink to confirm the settings change. DMX modes for POI are the same as for the 
standard. Visit www.sgmlight.com to see all DMX charts available under the respective product, or upon re

-

quest via [email protected].

• 

STEP 3: If necessary for the application, click advanced settings to set the fan mode, dimming curve, calibra

-

tion, or to reset to factory defaults.

• 

STEP 4: Disconnect POI uploader cable.

Repeat as required for multiple fixtures.

PLEASE NOTE! REMOTE DEVICE MANAGEMENT (RDM) REQUIRES A CORRECTLY INSTALLED AND TERMINATED 

DMX CABLE.

When setting addresses through RDM and using USB dongles, it may be necessary to disable “USB selective sus

-

pend” to ensure a proper voltage to the DMX link. If any lag or trouble occurs when addressing, decrease the cable 
length range to <12 m. and only address one fixture at a time.

Figure 11: SGM Addressing tool

SETTINGS AND FIXTURE DEFAULTS

Summary of Contents for i-2UVA









































Reviews:

No comments