manualshive.com logo in svg

ISGM i-2UVA, User Manual, Page: 12 / 40

Share
Download
ISGM i-2UVA User Manual Download Page 12

12

Product Version 1.0 | Revision A | Released 2022-2-21

CONNECTING POWER

The power cable color coding is given in figure 6:

• 

Connect the black wire to live

• 

Connect the white wire to neutral

• 

Connect the green/yellow wire to ground (earth)

For a temporary outdoor installation the mains cable must be fitted with a grounded connector intended for exterior 
use.
For permanent installations, have a qualified electrician wire the mains cable directly to a suitable branch circuit. Any 
cable management must have an appropriate (IP) rating suitable for the location. Always use a junction box with a 
proper IP class suitable for the environment.
After connecting the i-2 UVA to power, run the on-board test by selecting the option TEST→ SELF-TEST in the menu to 
ensure that the fixture and each LED are functioning correctly. POI versions have to be tested through RDM.

PLEASE NOTE!

THE PROTECTIVE CAPS MUST BE SECURELY MOUNTED ON ANY UNUSED CONNECTORS, IN ORDER TO MAIN

-

TAIN THE INGRESS PROTECTION (IP RATING).

CAUTION!
DO NOT OPEN THE FIXTURE TO REPLACE THE SUPPLIED POWER CABLE.
DO NOT CONNECT THE FIXTURE TO AN ELECTRICAL DIMMER SYSTEM, AS DOING SO MAY 

CAUSE DAMAGE.

CONNECTING A WIRELESS TRANSMITTER

The i-2 UVA is designed to look for wireless transmitters in ‘connect’ state when this option is not yet enabled. The 
fixture comes tested for wireless functionality from the factory, therefore the beginning of the pairing process is to 
disconnect from the factory wireless DMX transceiver.
To connect the i-2 UVA to a wireless transmitter:
Log off the currently paired wireless transmitter. Go to SETTINGS → WIRELESS DMX → LOG OFF in the menu. Fixture 
confirms logged off.

1.  Press the connect button on the wireless transmitter.

2. 

Confirm that the fixture has paired with the wireless transmitter.

PLEASE NOTE! FOR POI VERSIONS, REFER TO “WIRELESS DATA CONNECTION”.

SIGNAL PRIORITY

The i-2 UVA can be paired to an active wireless transmitter simultaneously when connected to a cabled DMX. The 
fixture will prioritize cabled DMX over wireless DMX. 
The active input type is displayed under the wireless signal strength indicator. The signal strength can be also checked 
via RDM data by using an external RDM device.

PLEASE NOTE! IN POI VERSION WITH WIRELESS, THE DMX SIGNAL STRENGTH IS CHECKED THROUGH RDM.

The fixture must be grounded/

earthed and be able to be isolated 

from AC power. The AC power 

supply must incorporate a fuse or 

curcuit breaker for fault protection.

Color

Black

White

green/yellow

Conductor

live

neutral

ground (earth)

Symbol

or

L

N

Wire

Figure 6: Connecting AC Power

Summary of Contents for i-2UVA









































Reviews:

No comments