x
1R
Smart
Non contractual document. Subject to change. Cod. 60000FSURM000.1 - 20191216
OEM Fingerprint Reader Installation Guide (EN) - © 2019 Iseo Serrature S.p.a. - www.iseo.com
OEM Fingerprint Surface Mounted Reader
ELECTRONIC SUPPORT SERVICE
iseozero1
.com
®
i s e o
. c o m
Iseo Serrature s.p.a
Via San Girolamo 13
25055 Pisogne (BS)
ITALY
Tel. +39 0364 8821
[email protected]
Download
Iseo Argo App
WARNINGS
Read this manual prior to use the device in order to ensure a safe and proper use.
Preserve this manual as future reference.
The installation and maintanance of the device must be carried out by qualified technical staff, adequately
trained by ISEO.
The instructions should be carefully followed during installation. These instructions and any maintenance
instructions should be passed on by the installer to the user.
No modifications of any kind are permitted, except for those described in these instructions.
The product must be destined only for the use for which it is expressly designed and therefore as a
fingerprint reader for civil and industrial locations. Any other use is considered improper and dangerous.
The electrical connection must be made according to the constructor's instructions and respecting the
regulations in force.
Disconnect the power supply before carrying out any technical service that involves opening or accessing
the internal parts of the product. For all repairs, exclusively contact a technical assistance center authorized
by the constructor.
app.iseo.com
ARGO
Download
User Manual
1. COMPONENTS
3. INSTALLATION EXAMPLE
UM = mm
Operating temperature: -20°C/+55°C with Relative Humidity Max. 90% without condensing.
https://www.iseo.com/it/en/download
OEM Surface
Mounted Reader
Reader connection
cable (to x1r Smart)
Cable length = 1mt.
Electronic board inside:
do not bend, crush or twist.
53
32
13,5
MAX 1mt
4. ELECTRICAL CONNECTION
Connect the cable to the x1R Smart,
in the Fingerprint Reader connector
(3rd connector from the bottom).
Before connecting the Fingerprint
Reader cable to x1R Smart, remove
the plug from the connector.
Fingerprint Reader cable
(1mt length).
Electronic board
: do not bend,
crush or twist. Install it with
care inside the door, without
any pressure, friction or folds.
6. CORRECT AND INCORRECT USE
5. INFORMATION ABOUT BIOMETRIC AUTHENTICATION
The fingerprint registration process is the most important part of the correct biometric template creation
and subsequent fingerprint identification. To know how to add fingerprints to
x1R Smart
, refer to the
Argo
User Manual
available at
app.iseo.com
.
Biometric authentications may vary depending from person, environmental conditions or incorrect use: exposure
to abrasive surfaces, glues, solvents, powders, cement, excessive moisture, could compromise the fingerprint
biometric authentication. Dirty, wet, dry, cut or damaged fingers may not be properly registered or identificated.
Children up to 5 years old could not be properly registered. A children’s fingerprint should be registered every
6 months.
It is recommended to register index, middle or ring finger as the thumb and little finger could be more
difficult to register and use.
Try to not press too hard or too soft on the optical sensor. Firmly place your finger on the sensor with
appropriate pressure. A wet or too dry finger may not be properly registered or identificated.
It is recommended to memorize for each user not only the fingerprint but also other credentials like PIN,
cards, smartphones, to be used in case the fingerprint technology does not work.
It is recommended to add more than one fingerprint for the same person. In this way in case your finger
fails to be recognized for example because cut, scarred or damaged, you can use the other one.
Make sure finger is always placed in the center of the optical sensor and placed firmly down. Always touch
with the center of the fingerprint (fingerprint’s core), as the tip of the finger will not register correctly. For
more information about correct finger position, refer to the
Argo User Manual
at
app.iseo.com
.
2. IP66 VERSION
IP66 Surface Mounted reader
with cable an IP66 connector
code:
5E62220
x1R Smart
connector
IP66 Reader
connector
IP66 cable
L=
1,2mt
code:
0000IS00246
IP66 cable
L=
10mt
code:
0000IS00247
min.50cm
min.50cm
part that can
be shortened
WARNING 0000IS00247
ISEO reccomends to not cut
the cable but to collect the
exceeding part inside the
door or the electric box. If
this is not possible and it’s
really necessary to shorten
it, cut a piece only where
indicated and properly join it.
