background image

Camera Overview

The diagram below details the various parts of your 
camera:

Warning!

Camera Installation Sequence

The diagram below shows the sequence in which the 
camera parts are fit into place during installation...

Warning!

It is strongly advised that the camera is powered up 
and connected to a monitor / computer to check the 
desired  field  of  view  prior  to  fixing  the  camera  in 
place.
Iris  do  not  accept  any  liability  if  the  camera  is 
installed and does not cover desired field of view.

1. Fit Base

2. Slide camera cable through base

3. Set desired camera field of view

4. Slide Cowling over inner dome onto base

5. Tighten Grub Screws

Iris Innovations

IRIS460 User Guide v2.01 May 2018

6

Inner Dome

Lens

Photo-Diode
(Light Sensor)

Infra Red LEDs

Cowling

Lock Screw
(in 2 positions)

Base

FULLY LOOSEN PRIOR TO 

ADJUSTING INNER DOME POSITION

(BOTH SIDES OF CAMERA)

TO AVOID DAMAGE TO THE CAMERAS PAINTWORK 
WHICH  COULD  RESULT  IN  EROSION  TO  THE 
HOUSING, ENSURE THE GRUB SCREWS ARE FULLY 
LOOSENED  BEFORE  MAKING  ANY  POSITIONAL 
ADJUSTMENTS TO THE INNER DOME. 
FAILURE  TO  DO  SO  WILL  INVALIDATE  ANY 
WARRANTY  CLAIM  IF  THE  PAINTWORK  IS 
SCRATCHED OR DAMAGED.

Summary of Contents for IRIS460





















Reviews: