background image

8

DALL ARA  iR01 | USER 

MANUAL

“QUAL“ PAGE

LEFT CLUSTER

RPM

 

  Engine 

RPM

SPEED

   

 

Vehicle Speed (MPH or KPH, depending on selected units)

BRAKE BALANCE

 

% Front brake bias

PEDAL

   

 

Currently selected throttle map setting

FARB

   

 

Current Front Anti-Roll Bar blade setting

RARB

   

 

Current Rear Anti-Roll Bar blade setting

RIGHT CLUSTER

LAP TIME

 

 

Current Lap Time

GAIN/LOSS

 

 

Time difference to session best lap

FUEL REMAINING

 

Fuel level in the car (Gallons or Liters, depending on selected units)

BOTTOM ROW

TIRE TEMP

 

 

Current surface temperature for each tire (°C or °F)

TIRE PRESS

 

 

Current tire pressure for each tire (psi or kPa)

DISPL AY NOTIFICATIONS

There are several warnings that will come up on the display. The top two lights on the left and right side are wheel lock indicators 
that will indicate that one of the tires is sliding through the braking zone. The display will flash red when oil or water temp exceed 
their limits of 100 C, and it will flash red when there are 3 laps of fuel left in the tank. The pit limiter will make the screen turn blue 
and the lights on the side will flash. When water or oil pressure is lost, a message will show up on the bottom line of the screen 
indicating what the problem is. The display will also turn red in that case.

DALLARA iR01 | DASH 

PAGES

Summary of Contents for Dallara IR-01




















Reviews: