IPSO HC100 Instruction Manual Download Page 28

Page: 28 / 35

After programming the price for the last program, there are still the following
parameters :

A : Eco - price

This is the decrease in value of the price for economical wash. In other words,
the amount that the customer is saving by using economic wash.

B : Number of coin insertions COIN 1 (up to 60.000)

This parameter is only indicated if it has been programmed as such in the program-
mation (COIN COUNT).

C : Number of coin insertions COIN 2 (up to 60.000)

This parameter is only indicated if it has been programmed as such in the program-
mation (COIN COUNT).

D : Info manufacturer or technician

TMP T/N : Info manufacturer or technician.

Here you can program the temperature to appear on display in case this has not
been done at the programmation.

When all desired programs are provided with the right price, end the operation by
pressing the push button or pulling over the coin meter switch-lever.

Summary of Contents for HC100




































Search results

Summary of Contents for HC100

Reviews:

Related manuals for HC100

Brands by name

Popular brands

IPSO HC100, Instruction Manual

Search results

Summary of Contents for HC100

Reviews:

Related manuals for HC100

Brands by name

Popular brands