background image

MIG-160ER 

 

 

14 

 

An arc is created as 
soon as the gas 
nozzle is touched 

Short circuit between electricity 
and gas nozzle 

Clean the gas nozzle and torch 
neck and spray with welding 
spray 

Torch gets too hot 

Contact tip too big or loose 

Use a contact tip suitable for the 
wire size or screw the tip tight 

10 

Insufficient welding 
current 

Bad contact 

Check ground cable and pliers 
or hose package, replace if 
necessary 

 

 

PROPER DISPOSAL 

 
In accordance with the DIRECTIVE OF THE EUROPEAN PARLIAMENT AND THE COUNCIL on waste 
electrical and electronic equipment and its implementation in national law, used power tools must be 
collected separately and recycled in an environmentally friendly manner. 

CAUTION! Do not throw away power tools in the household waste! 

The device consists of various materials that must be collected separately, as it can contain 
both environmentally harmful substances and valuable raw materials such as aluminium, 
which must be disposed of properly. The trash can symbol indicates the need for separate 
collection. 

 

You  too  can  help  protect  the  environment  and  ensure  that  as  many  resources  as  possible  are  used 
again and that the environment is preserved. If you no longer wish to use this device, please take it to 
the system provided for this purpose, the local recycling centre, so that it can be disposed of there. 

For this purpose, the public waste disposal authorities set up collection points where old devices from 
private households in their area can be accepted free of charge. The legal disposal authorities may also 
collect the old devices from private households. - Please check your local waste calendar or your city or 
local authority for information about the return or collection options for waste equipment in your area. 

BATTERIES 

Do  not  dispose  of  the  batteries  with  household  waste.  Batteries  are  pre-installed  in  the  toolbox  and 
cannot be removed from the tool by the user. The disposal of the battery must only be carried out by a 
specialist. 

The  use  of  these  substances  in  new  devices  is  severely  restricted  by  the  Electrical  and  Electronic 
Equipment Act. In some components, however, it is still necessary to use them today, so that the old 
devices often still contain significant amounts of pollutants. 

 

 

MANUFACTURER WARRANTY 

 

1.  MANDATORY WARRANTY 

IPO Technik-Handels GmbH grants a warranty to all customers for all welding machines and/or plasma 
cutters purchased directly from IPO Technik-Handels GmbH of the IPOTOOLS brand. 

All devices are subject to a 2-year statutory warranty from the invoice date under the warranty conditions 
below and if it is not due to incorrect or careless handling by the customer. 
 

Summary of Contents for MIG-160ER


















Reviews: