background image

3. GENERAL

OC29 X.Lite ProCap is a high-speed process tracing system in the medium performance and price segment. USB3 is 

used to transfer the images directly and quickly to the PC/laptop. Next, the available documents/media are listed and 

the use and disposal are defined. 

3.1.

 

Document scope 

-

Product data sheet

-

Manual (this document)

Information relevant within the scope of OC29 X.Lite ProCap are covered within the scope of this documen-

tation. Information that goes beyond this shall be indicated at the appropriate positions (mainly in the hard-

ware chapter). 

4. SYSTEM COMPONENTS

The core components of the OC29 X.Lite ProCap system are a USB3 camera, the associated transmission cable, and 

the software (supplied on USB stick) for recording and depicting image data. The system can be adjusted to the re-

spective requirements by adding additional accessories.   

An overview of the currently available system components is provided in the "Hardware" chapter. 

4.1.

 

For whom is this manual intended? 

This manual is intended for all persons who set up, put into operation, dismantle, carry out maintenance and operate 

the OC29 X.Lite ProCap system. 

It must be ensured that the operating personnel and all additional personnel who come into contact with the the 

OC29 X.Lite ProCap system have read and understood this user manual. 

4.2.

 

Intended use 

The OC29 X.Lite ProCap system is used for the analysis and documentation of very fast industrial processes (handling 

tasks, presses, etc.).  

 In this case, read the safety conditions for use within plant environments in chapter 2! 

Observe the guarantee instructions with regard to functionality and performance with the installation instructions 

(following chapter) and system requirements (hardware chapter)! 

4.3.

 

Disposal 

During disposal, local regulations concerning the respective components must be observed! 

MANUAL • Subject to alteration! Version: 

September 2019

 

ipf electronic gmbh • Rosmarter Allee 14 • 58762 Altena 

 Tel +49 2351 9365-0 • Fax +49 2351 9365-19 

 [email protected] • www.ipf-electronic.com 

3

Summary of Contents for OC29 X.Lite ProCap















Reviews: