iPECS iPECS-LIK Feature Description & Operation Download Page 87

Page: 87 / 447

iPECS-LIK
Feature Description & Operation Manual

Issue 6.0d1

Conditions

1. The conditions associated with Multi-Party Voice Conference apply.

2. Members using the iPECS Phontage or UCS client may view the state of other

members in the conference.

3. The number of available groups is given in Table 1.2-1 System Capacity Chart.

Each group can have up to 32 members including the supervisor.

4. The user must have access to the Station Web Admin with the proper password

(Authentication code).

5. If there are insufficient MCIM channels available when initiating the conference

group call, the initiator receives error tone.

6. Two-way record can be used to record the Conference Group call.

Programming

Related Features



Multi-Party Voice Conference



Conference Room



System Admin Programming

Hardware



MCIM

2.23.5 Conference Member VIEW & DELETE

Description

In Multi-Party conference,

Conference supervisor can see the conference member and remove the member from
conference.

Operation

1. Conference supervisor press

{VIEW}

soft button in conference.

LCD displays the first member. If member is a station, “STA XXX” display. If

member is a co line, telephone number of caller/called party in the co line display.

3. Conference supervisor can see other members by pressing

[VOLUME UP/DONW]

button. (Next member if

[VOLUME DOWN]

button, previous member if

[VOLUME

UP]

button)

4. If press

{DELETE}

soft button, the current member will be removed from

conference.

5. If press

{ADD}

soft button, the conference supervisor can add a new member.

6. If press

{BACK}

soft button, conference supervisor will be back to normal

conference state.

Summary of Contents for iPECS-LIK
































































































































































































































































































































































































































































Search results

Summary of Contents for iPECS-LIK

Reviews:

Related manuals for iPECS-LIK

Brands by name

Popular brands

iPECS iPECS-LIK, Feature Description & Operation

Search results

Summary of Contents for iPECS-LIK

Reviews:

Related manuals for iPECS-LIK

Brands by name

Popular brands