iPECS iPECS-LIK Feature Description & Operation Download Page 412

Page: 412 / 447

iPECS-LIK
Feature Description & Operation Manual

Issue 6.0d1

399

8. SIP

EXTENSION

8.1 REGISTRATION

Description

iPECS-LIK supports standard protocol equipped SIP Phone including series of Ericsson-LG
SIP Phone Extension.

Operation

SIP Phone Self Programming

Network Configuration

1. IP mode : Static(Fixed) / DHCP

2. Subnet Mask

3. Default gateway IP address

4. IP address

5. DNS IP address

6. Profiling (for Wireless)

SIP Server Configuration

1. Proxy IP address : MFIM IP address

2. Proxy IP port : 5060

3. Domain : MFIM IP address

4. Registration : ON

5. Registration Timer : 30 ~ 3600 second (more than 10 minute recommended)

6. Local UDP/TCP/TLS port : 5060 or other value

7. Signaling/Transport Mode : UDP (or TCP or TLS)

Line(User) Configuration

1. SIP Account :

− Display Name (Optional) : Station Name (this will be applied to MFIM – Station

Name).

− User Name (Mandatory) : Station Number (this should be same as MFIM –

Device

− Authorization Name (Mandatory) : Login ID (this should be same as MFIM –

Device

− Authorization Password (Optional) : Login Password Login ID (this should be

same as MFIM

– Device Login / Station User Login (443) / “Password”)

Call Preferences

1. Call Wait : ON / OFF (When on BUSY, accept other call setup or not)

2. Call Forward

3. DTMF Type (Mandatory) : one of INFO type (After registration to system, SIP Data /

SIP Phone Attributes(211) / “DTMF Type” – set the same type as SIP Phone) c.f)
only support INFO type

4. CODEC

Summary of Contents for iPECS-LIK
































































































































































































































































































































































































































































Search results

Summary of Contents for iPECS-LIK

Reviews:

Related manuals for iPECS-LIK

Brands by name

Popular brands

iPECS iPECS-LIK, Feature Description & Operation

Search results

Summary of Contents for iPECS-LIK

Reviews:

Related manuals for iPECS-LIK

Brands by name

Popular brands