iPECS iPECS-LIK Feature Description & Operation Download Page 317 | Manualshive

Page: 317 / 447

background image

iPECS-LIK
Feature Description & Operation Manual

Issue 6.0d1

304

4. This feature may not be available in the specific ISDN or may be a subscription

service.

5. The system can handle only a single Call Reference; services that require handling

of two simultaneous Call References, cannot be supported.

Programming

STATION

1 Flex Button Assignment (PGM 115)

Related Features



Station Speed Dial



System Speed Dial

Hardware



iPECS Phone



ISDN gateway Module

4.15.4 Multiple Subscriber Number (MSN)

Description

MSN enables up to 8 Subscriber Numbers to be allocated to one Basic Rate Interface allowing
Direct-Dial-In call delivery. Sub-Address information is included as additional digits in the Called
Party Number Information Element. These additional digits allow the system to ring a specific
station in the MSN pool of phone numbers, iPECS-Micro, iPECS-50 and MFIM100: 250,
MFIM300: 500, MFIM600: 1000 and MFIM1200:1500. When MSN or Sub-address information
is received, the system references the MSN Table for an index to the Flexible DID Table, which
determines call routing.

In addition, the MSN pool can be utilized for multiple calling number of station. If a station is
assigned a loop button that references a specific MSN entry, the specific MSN will be served as
a calling number of the station when make an outbound call over ISDN or SIP using the
assigned button.

Operation

System

Inbound Call

Automatic by programming of Called Telephone Number and Index of Flexible DID
Table in MSN pool.

Outbound Call

Press the assigned MSN Loop Button, and dial over ISDN or SIP.

The assigned MSN telephone number will be served for calling number. And it is
recorded by account code of call in SMDR.

«
...
315
316
317
318
319
...
»

Summary of Contents for iPECS-LIK
































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for iPECS-LIK

Brand: IDEETRON Pages: 12

Brand: Vega Pages: 39

Brand: Digi Pages: 6

BridgeX BX5020 GT Series

Brand: Mellanox Technologies Pages: 64

Brand: Kunbus Pages: 30

Brand: NXP Semiconductors Pages: 2

Brand: Cisco Pages: 76

Brand: Panasonic Pages: 68

Brand: Panasonic Pages: 68

Brand: Panasonic Pages: 76

Brand: Panasonic Pages: 174

WIRELESS DATA GATEWAY

Brand: Paradyne Pages: 66

Brand: VADcore Pages: 51

Brand: Grandstream Networks Pages: 2

Brand: ZyXEL Communications Pages: 2

Brand: Packet Media Pages: 7

Brand: ZyXEL Communications Pages: 35

Brand: Nexo Pages: 90

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands